 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Charge Pump, 7-Channel Fun Lighting LED Driver ADP8863 FEATURES Automated blinking and funlight timing for each LED driver 16 programmable fade in and fade out times 0.1 sec to 5.5 sec Selectable linear, square, or cubic fade rates 7 independent and programmable LED drivers 7 drivers capable of 30 mA (maximum) 1 driver also capable of 60 mA (maximum) Programmable maximum current limit (128 levels) Separate and independent controls for backlight LEDs Backlight fade override Up to two built-in comparator inputs with programmable modes for ambient light sensing Charge pump with automatic gain selection of 1x, 1.5x, and 2x for maximum efficiency Standby mode for <1 A current consumption I2C-compatible interface for all programming Dedicated reset pin and built-in power-on reset (POR) Short-circuit, overvoltage, and overtemperature protection Internal soft start to limit inrush currents Input-to-output isolation during faults or shutdown Operation down to VIN = 2.5 V with undervoltage lockout (UVLO) at VIN = 2.0 V Small lead frame chip scale package (LFCSP) TYPICAL OPERATING CIRCUIT VALS PHOTO SENSOR D1 VIN CIN 1F VDDIO C1+ C1- C2+ C2- C2 1F C1 1F D2 D3 D4 D5 D6 D7 CMP_IN 0.1F VOUT COUT 1F nRST nINT SDA SCL ADP8863 GND1 GND2 Figure 1. APPLICATIONS LED indication Funlight indicator lighting Keypad backlighting RGB LED color generation and mixing General backlighting of small format displays GENERAL DESCRIPTION The ADP8863 combines a powerful charge pump driver with advanced autonomous LED lighting features. It allows as many as seven LEDs to be independently driven up to 30 mA (maximum). The seventh LED can also be driven to 60 mA (maximum). All LEDs are programmable for maximum current and fade in/fade out times via the I2C interface. Additionally, automated blinking routines can be independently programmed and enabled for all seven LED channels. These LEDs can also be combined into groups to reduce the processor instructions. This entire configuration is driven by a two-capacitor charge pump with gains of 1x, 1.5x, and 2x. The charge pump is capable of driving a maximum IOUT of 240 mA from a supply of 2.5 V to 5.5 V. The device includes a variety of safety features including short-circuit, overvoltage, and overtemperature protection. These features allow easy implementation of a safe and robust design. Additionally, input inrush currents are limited via an integrated soft start combined with controlled input-to-output isolation. The ADP8863 is available in a compact lead frame chip scale package (LFCSP). Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2010 Analog Devices, Inc. All rights reserved. 08392-001 ADP8863 TABLE OF CONTENTS Features .............................................................................................. 1 Applications ....................................................................................... 1 Typical Operating Circuit ................................................................ 1 General Description ......................................................................... 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 I C Timing Diagram .................................................................... 4 Absolute Maximum Ratings............................................................ 5 Maximum Temperature Ranges ................................................. 5 Thermal Resistance ...................................................................... 5 ESD Caution .................................................................................. 5 Pin Configuration and Function Descriptions ............................. 6 Typical Performance Characteristics ............................................. 7 Theory of Operation ...................................................................... 11 Power Stage.................................................................................. 12 Operating Modes ........................................................................ 13 LED Groupings ........................................................................... 14 LED Current Settings ................................................................. 14 Automated Fade In and Fade Out ............................................ 14 Independent Sink Control......................................................... 15 RGB Color Generation .............................................................. 15 2 2 Automated RGB Color Fades ................................................... 15 Backlight Operating Levels ....................................................... 16 Backlight Turn On/Turn Off/Dim ........................................... 16 Automatic Dim and Turn Off Timers ..................................... 16 Fade Override ............................................................................. 17 Ambient Light Sensing .............................................................. 17 Automatic Backlight Adjustment ............................................. 18 Using the ADP8863 to Drive Additional LEDs...................... 19 Operating LEDs from Alternative Supplies ............................ 20 Short-Circuit Protection Mode ................................................ 21 Overvoltage Protection .............................................................. 21 Thermal Shutdown/Overtemperature Protection ................. 21 Interrupts ..................................................................................... 21 Applications Information .............................................................. 23 Layout Guidelines....................................................................... 23 I C Programming and Digital Control ........................................ 24 Backlight Register Descriptions ............................................... 29 Independent Sink Register Descriptions................................. 36 Comparator Register Descriptions .......................................... 44 Outline Dimensions ....................................................................... 48 Ordering Guide .......................................................................... 48 REVISION HISTORY 4/10--Revision 0: Initial Version Rev. 0 | Page 2 of 48 ADP8863 SPECIFICATIONS VIN = 3.6 V, SCL = 2.7 V, SDA = 2.7 V, nINT = open, nRST = 2.7 V, CMP_IN = 0 V, VD1:D7 = 0.4 V, Capacitor C1 = 1 F, Capacitor C2 = 1 F, COUT = 1 F, typical values are at TA = 25C and are not guaranteed, minimum and maximum limits are guaranteed from TA = -40C to +85C, unless otherwise noted. Table 1. Parameter SUPPLY Input Voltage Operating Range Start-Up Level Low Level VIN(START) Hysteresis UVLO Noise Filter Quiescent Current Prior to VIN(START) During Standby After Startup and Switching OSCILLATOR Switching Frequency Duty Cycle OUTPUT CURRENT CONTROL Maximum Drive Current D1 to D7 TJ = 25C TJ = -40C to +85C D7 Only (60 mA Setting) TJ = 25C TJ = -40C to +85C LED Current Source Matching 1 All Current Sinks D2 to D7 Current Sinks Leakage Current on LED Pins Equivalent Output Resistance Gain = 1x Gain = 1.5x Gain = 2x Regulated Output Voltage AUTOMATIC GAIN SELECTION Minimum Voltage Gain Increases Minimum Current Sink Headroom Voltage Gain Delay AMBIENT LIGHT SENSING COMPARATORS Ambient Light Sensor Current DAC Bit Step Threshold L2 Level Threshold L3 Level FAULT PROTECTION Start-Up Charging Current Source Symbol Test Conditions/Comments Min Typ Max Unit VIN VIN(START) VIN(STOP) VIN(HYS) tUVLO IQ IQ(START) IQ(STBY) IQ(ACTIVE) 2.5 VIN increasing VIN decreasing After startup 1.75 2.05 1.97 80 10 10 0.3 4.5 5.5 2.30 V V V mV s A A mA VIN = VIN(START) - 100 mV VIN = 3.6 V, Bit nSTBY = 0, SCL = SDA = 0 V VIN = 3.6 V, Bit nSTBY = 1, IOUT = 0 mA, gain = 2x 0.8 1.0 7.2 fSW D ID1:D7(MAX) VD1:D7 = 0.4 V Bit SCR = 0 in the ISC7 register 1 50 1.32 MHz % 26.2 24.4 ID7(60 mA) VD7 = 0.4 V, Bit SCR = 1 in the ISC7 register 52.5 48.8 IMATCH IMATCH7 IMATCH6 ID1:D7(LKG) ROUT VD1:D7 = 0.4 V VD2:D7 = 0.4 V VIN = 5.5 V, VD1:D7 = 2.5 V, Bit nSTBY = 1 VIN = 3.6 V, IOUT = 100 mA VIN = 3.1 V, IOUT = 100 mA VIN = 2.5 V, IOUT = 100 mA VIN = 3 V, gain = 2x, IOUT = 10 mA 30 34.1 34.1 67 67 mA mA mA mA % % A V 60 2.0 1.5 0.5 0.5 3.0 3.8 4.9 VOUT(REG) 4.3 5.5 VHR(UP) VHR(MIN) tGAIN Decrease VD1:D7 until the gain switches up IDX = IDX(MAX) x 95% The delay after gain has changed and before gain is allowed to change again 162 200 180 100 276 mV mV s IALS IL2BIT IL3BIT ISS CMP_IN = VD6 = 2.8 V, Bit CMP2_SEL = 1 IL2BIT = IALS/250 IL3BIT = IALS/2000 VIN = 3.6 V, VOUT = 0.8 x VIN Rev. 0 | Page 3 of 48 0.70 1.08 4.3 0.54 1.33 mA A A 2.5 3.75 5.5 mA ADP8863 Parameter Output Voltage Threshold Exit Soft Start Short-Circuit Protection Output Overvoltage Protection Activation Level OVP Recovery Hysteresis Thermal Shutdown Threshold Hysteresis Isolation from Input to Output During Fault Time to Validate a Fault I2C INTERFACE Operating VDDIO Voltage Logic Low Input 2 Logic High Input 3 2 I C TIMING SPECIFICATIONS Delay from Reset Deassertion to I2C Access SCL Frequency SCL High Time SCL Low Time Setup Time Data Repeated Start Stop Condition Hold Time Data Start/Repeated Start Bus Free Time (Stop and Start Conditions) Rise Time (SCL and SDA) Fall Time (SCL and SDA) Pulse Width of Suppressed Spike Capacitive Load per Bus Line 1 2 3 Symbol VOUT VOUT(START) VOUT(SC) VOVP VOVP(HYS) TSD TSD(HYS) IOUTLKG tFAULT VDDIO VIL VIH tRESET fSCL tHIGH tLOW tSU, DAT tSU, STA tSU, STO tHD, DAT tHD, STA tBUF tR tF tSP CB Test Conditions/Comments VOUT rising VOUT falling Min Typ 0.92 x VIN 0.55 x VIN 5.8 500 150 20 Max Unit V V V mV C C A s VIN = 5.5 V, VOUT = 0 V, Bit nSTBY = 0 2 1.5 VIN = 3.6 V VIN = 3.6 V Guaranteed by design 5.5 0.6 1.30 20 400 0.6 1.3 100 0.6 0.6 0 0.6 1.3 20 + 0.1 CB 20 + 0.1 CB 0 0.9 V V V s kHz s s ns s s s s s ns ns ns pF 300 300 50 400 Current source matching is calculated by dividing the difference between the maximum and minimum current from the sum of the maximum and minimum. VIL is a function of the input voltage. See Figure 15 in the Typical Performance Characteristics section for typical values over operating ranges. VIH is a function of the input voltage. See Figure 15 in the Typical Performance Characteristics section for typical values over operating ranges. I2C TIMING DIAGRAM SDA tLOW SCL tR tSU, DAT tF tF tHD, STA tSP tR tBUF S tHD, DAT tHIGH tSU, STA Sr tSU, STO P S 08392-002 S = START CONDITION Sr = REPEATED START CONDITION P = STOP CONDITION Figure 2. I2C Interface Timing Diagram Rev. 0 | Page 4 of 48 ADP8863 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter VIN, VOUT D1, D2, D3, D4, D5, D6, and D7 CMP_IN nINT, nRST, SCL, and SDA Output Short-Circuit Duration Operating Ambient Temperature Range Operating Junction Temperature Range Storage Temperature Range Soldering Conditions ESD (Electrostatic Discharge) Human Body Model (HBM) Charged Device Model (CDM) 1 MAXIMUM TEMPERATURE RANGES Rating -0.3 V to +6 V -0.3 V to +6 V -0.3 V to +6 V -0.3 V to +6 V Indefinite -40C to +85C1 -40C to +125C -65C to +150C JEDEC J-STD-020 3 kV 1.5 kV The maximum operating junction temperature (TJ(MAX)) takes precedence over the maximum operating ambient temperature (TA(MAX)). Therefore, in situations where the ADP8863 is exposed to poor thermal resistance and high power dissipation (PD), the maximum ambient temperature may need to be derated. In these cases, the maximum ambient temperature can be calculated with the following equation: TA(MAX) = TJ(MAX) - (JA x PD(MAX)) THERMAL RESISTANCE JA (junction to air) is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. The JA, JB (junction to board), and JC (junction to case) are determined according to JESD51-9 on a 4-layer printed circuit board (PCB) with natural convection cooling. For the LFCSP package, the exposed pad must be soldered to the GND1 and/or GND2 terminal(s) on the board. Table 3. Thermal Resistance Package Type 20-Lead LFCSP_WQ JA 49.5 JC 5.3 Unit C/W The maximum operating junction temperature (TJ(MAX)) takes precedence over the maximum operating ambient temperature (TA(MAX)). See the Maximum Temperature Ranges section for more information. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Absolute maximum ratings apply individually only, not in combination. Unless otherwise specified, all voltages are referenced to ground. ESD CAUTION Rev. 0 | Page 5 of 48 ADP8863 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 18 CMP_IN 20 D4 19 D5 17 D6 16 D7 D3 1 D2 2 D1 3 SCL 4 nRST 5 15 GND1 ADP8863 TOP VIEW (Not to Scale) 14 VIN 13 VOUT 12 C2+ 11 C1+ 8 9 C1- nINT SDA 7 NOTES 1. CONNECT THE EXPOSED PADDLE TO GND1 AND/OR GND2. GND2 C2- 10 6 Figure 3. Pin Configuration Table 4. Pin Function Descriptions Pin No. 14 3 2 1 20 19 17 16 18 13 11 9 12 10 15 8 6 5 7 4 21 Mnemonic VIN D1 D2 D3 D4 D5 D6 D7 CMP_IN VOUT C1+ C1- C2+ C2- GND1 GND2 nINT nRST SDA SCL EPAD Description Input Voltage, 2.5 V to 5.5 V. LED Sink 1. LED Sink 2. LED Sink 3. LED Sink 4. LED Sink 5. LED Sink 6. This pin can also be selected as a comparator input for the second phototransistor. LED Sink 7. Comparator Input for Phototransistor. When using this function, a capacitor (0.1 F recommended) must be connected from this pin to ground. Charge Pump Output. Charge Pump C1+. Charge Pump C1-. Charge Pump C2+. Charge Pump C2-. Ground. Connect the exposed pad to GND1 and/or GND2. Ground. Connect the exposed pad to GND1 and/or GND2. Processor Interrupt (Active Low). Requires an external pull-up resistor. If this pin is not used, it can be left floating. Hardware Reset (Active Low). This pin resets the device to the default conditions. If not used, this pin must be tied above VIH(MIN). I2C Serial Data. Requires an external pull-up resistor. I2C Clock. Requires an external pull-up resistor. Exposed Paddle. Connect the exposed paddle to GND1 and/or GND2. Rev. 0 | Page 6 of 48 08392-003 ADP8863 TYPICAL PERFORMANCE CHARACTERISTICS VIN = 3.6 V, SCL = 2.7 V, SDA = 2.7 V, nRST = 2.7 V, VD1:D7 = 0.4 V, CIN = 1 F, Capacitor C1 = 1 F, Capacitor C2 = 1 F, COUT = 1 F, TA= 25C, unless otherwise noted. 2.0 1.8 1.6 1.4 IOUT = NO LOAD 35 30 25 IOUT (mA) VIN = 3.6V ID1:D7 = 30mA 1.2 IQ (mA) 20 15 10 D1 D2 D3 D4 D5 D6 D7 0 0.2 0.4 0.6 0.8 1.0 VHR (V) 1.2 1.4 1.6 1.8 2.0 08392-007 1.0 0.8 0.6 0.4 0.2 0 1.5 2.0 2.5 3.0 3.5 VIN (V) 4.0 4.5 -40C +25C +85C +105C 5.0 5.5 08392-004 5 0 Figure 4. Typical Quiescent Current, G = 1x 5.0 4.5 4.0 3.5 IOUT = NO LOAD Figure 7. Typical Diode Current vs. Current Sink Headroom Voltage (VHR) 35 34 33 32 VD1:D7 = 0.4V IOUT (mA) 3.0 31 30 29 28 D1 D2 D3 D4 D5 D6 D7 2.5 3.0 3.5 4.0 VIN (V) 4.5 5.0 5.5 08392-008 08392-009 IQ (mA) 2.5 2.0 1.5 1.0 0.5 0 1.5 2.0 2.5 3.0 3.5 VIN (V) 4.0 4.5 -40C +25C +85C +105C 5.0 5.5 08392-005 27 26 25 2.0 Figure 5. Typical Quiescent Current, G = 2x, IQ(ACTIVE) 10 6 Figure 8. Typical Diode Matching vs. VIN SCL = SDA = 0V nRST = 2.7V 5 1 MISMATCH (%) -40C +25C +85C +105C VIN = 3.6V ID1:D7 = 30mA 4 IQ (A) 0.1 3 2 0.01 -40C +25C +85C +105C 08392-006 1 0.001 0 1 2 3 VIN (V) 4 5 6 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 VHR (V) Figure 6. Typical Standby IQ vs. VIN Figure 9. Typical Diode Matching vs. Current Sink Headroom Voltage (VHR) Rev. 0 | Page 7 of 48 ADP8863 35 30 25 IOUT (mA) VIN = 3.6V ID1:D7 = 30mA 1.0 0.9 0.8 0.7 ROUT () IOUT = 100mA 20 15 10 5 0 -40C +25C +85C +105C 0 0.2 0.4 0.6 0.8 1.0 VHR (V) 1.2 1.4 1.6 1.8 2.0 08392-010 0.6 0.5 0.4 0.3 0.2 0.1 0 2.0 2.5 3.0 3.5 4.0 VIN (V) 4.5 -40C +25C +85C +105C 5.0 5.5 08392-013 08392-015 08392-014 Figure 10. Typical Diode Current vs. Current Sink Headroom Voltage (VHR) 1 0 -1 -2 -3 -4 -5 -6 -40 IOUT (mA) Figure 13. Typical ROUT (G = 1x) vs. VIN 10 9 8 VIN = 3.6V VD1:D7 = 0.40V VOUT = 80% OF VIN IOUT DEVIATION (%) 7 6 5 4 3 2 1 08392-011 -40C +25C +85C +105C 2.5 3.0 3.5 4.0 VIN (V) 4.5 5.0 5.5 -10 20 50 80 110 0 2.0 JUNCTION TEMPERATURE (C) Figure 11. Typical Change In Diode Current vs. Temperature 7 6 5 ROUT () Figure 14. Typical Output Soft Start Current, ISS 1.4 VIH @ +25C 1.2 1.0 VIH @ +85C VIH @ -40C IOUT = 100mA 4 3 G = 2x @ VIN = 2.5V THRESHOLD (V) 0.8 VIL @ +25C 0.6 0.4 0.2 0 2.5 VIL @ +85C VIL @ -40C G = 1.5x @ VIN = 3V 2 1 0 -40 G = 1x @ VIN = 3.6V 08392-012 -20 0 20 40 60 80 100 3.0 3.5 4.0 VIN (V) 4.5 5.0 5.5 TEMPERATURE (C) Figure 12. ROUT vs. Temperature Figure 15. Typical I2C Thresholds, VIH and VIL Rev. 0 | Page 8 of 48 ADP8863 1.4 1.3 1.2 IALS (mA) 90 80 70 450 400 350 300 1.0 0.9 0.8 0.7 2.5 -40C +25C +85C +105C 3.0 3.5 4.0 VIN (V) 4.5 5.0 5.5 08392-035 40 30 20 10 0 2.5 IOUT = 140mA, Vf = 3.1V IOUT = 210mA, Vf = 3.2V 3.0 3.5 4.0 VIN (V) 4.5 5.0 200 150 100 50 0 5.5 IIN (mA) 1.1 EFFICIENCY (%) 60 50 250 Figure 16. Typical ALS Current, IALS 5.5 5.4 5.3 5.2 VOUT (V) Figure 19. Typical Efficiency (Low Vf Diode) 100 90 80 70 450 400 350 300 VIN = 3V GAIN = 2x IOUT = 10mA 5.1 5.0 4.9 4.8 4.7 4.6 -10 20 50 80 110 08392-016 EFFICIENCY (%) 60 50 40 30 20 10 IOUT = 140mA, Vf = 3.85V IOUT = 210mA, Vf = 4.25V 3.0 3.5 4.0 VIN (V) 4.5 5.0 200 150 100 50 0 5.5 4.5 -40 JUNCTION TEMPERATURE (C) Figure 17. Typical Regulated Output Voltage (VOUT(REG)) 6.0 Figure 20. Typical Efficiency (High Vf Diode) T VIN (AC-COUPLED) 50mV/DIV 1 5.8 OVP THRESHOLD VOUT (V) VOUT (AC-COUPLED) 50mV/DIV 5.6 2 5.4 OVP RECOVERY IIN (AC-COUPLED) 10mA/DIV 3 08392-020 CIN = 1F, COUT = 1F, C1 = 1F, C2 = 1F VIN = 3.6V IOUT = 120mA 500ns/DIV -10 20 50 80 110 JUNCTION TEMPERATURE (C) Figure 18. Typical Overvoltage Protection (OVP) Threshold 08392-017 5.2 -40 Figure 21. Typical Operating Waveforms, G = 1x Rev. 0 | Page 9 of 48 08392-019 0 2.5 IIN (mA) 250 08392-018 ADP8863 T VIN (AC-COUPLED) 50mV/DIV 1 CIN = 10pF, COUT = 1F C1 = 1F, C2 = 1F VIN = 3.7V IOUT = 30mA (ONE DIODE AT MAX CURRENT) VOUT (1V/DIV) VOUT (AC-COUPLED) 50mV/DIV 2 2 IIN (AC-COUPLED) 10mA/DIV 3 08392-021 IIN (10mA/DIV) 500ns/DIV 4 IOUT (10mA/DIV) 100s/DIV Figure 22. Typical Operating Waveforms, G = 1.5x Figure 24. Typical Start-Up Waveform T VIN (AC-COUPLED) 50mV/DIV 1 VOUT (AC-COUPLED) 50mV/DIV 2 IIN (AC-COUPLED) 10mA/DIV 3 08392-022 CIN = 1F, COUT = 1F, C1 = 1F, C2 = 1F VIN = 2.5V IOUT = 120mA 500ns/DIV Figure 23. Typical Operating Waveforms, G = 2x Rev. 0 | Page 10 of 48 08392-023 CIN = 1F, COUT = 1F, C1 = 1F, C2 = 1F VIN = 3.0V IOUT = 120mA ADP8863 THEORY OF OPERATION The ADP8863 combines a powerful LED charge pump driver with independent control of up to seven LEDs. These LED drivers can sink up to 30 mA (typical) on six channels. The seventh LED can also be driven to 60 mA (typical). All LEDs can be individually programmed or combined into a group to operate backlight LEDs. A full set of safety features, including short-circuit, overvoltage, and overtemperature protection with input-to-output isolation, allows for a robust and safe design. The integrated soft start limits inrush currents at startup, restart attempts, and gain transitions. VALS OPTIONAL PHOTOSENSOR D1 D2 D3 D4 D5 D6 D7 GAIN SELECT LOGIC CMP_IN VIN PHOTOSENSOR CONVERSION ISS ID1 ID2 ID3 ID4 ID5 ID6 ID7 VIN VREFS IREFS EN CLK CHARGE PUMP LOGIC SOFT START VIN UVLO VIN VBAT CIN VOUT COUT VDDIO STNDBY NOISE FILTER nRST 50s C1+ LIGHT SENSOR LOGIC STANDBY C1 1F C1- C2+ C2 1F C2- SWITCH CONTROL CURRENT SINK CONTROL RESET SCL I2C SDA LOGIC CHARGE PUMP (1x, 1.5x, 2x) nINT GND1 GND2 Figure 25. Detailed Block Diagram Rev. 0 | Page 11 of 48 08392-024 ADP8863 POWER STAGE Because typical white LEDs require up to 4 V to drive them, some form of boosting is required over the typical variation in battery voltage. The ADP8863 accomplishes this with a high efficiency charge pump capable of producing a maximum IOUT of 240 mA over the entire input voltage range (2.5 V to 5.5 V). Charge pumps use the basic principle that a capacitor stores charge based on the voltage applied to it, as shown in the following equation: Q=CxV (1) By charging the capacitors in different configurations, the charge, and therefore the gain, can be optimized to deliver the voltage required to power the LEDs. Because a fixed charging and discharging combination must be used, only certain multiples of gain are available. The ADP8863 is capable of automatically optimizing the gain (G) from 1x, 1.5x, and 2x. These gains are accomplished with two capacitors (labeled C1 and C2 in Figure 25) and an internal switching network. In G = 1x mode, the switches are configured to pass VIN directly to VOUT. In this mode, several switches are connected in parallel to minimize the resistive drop from input to output. In G = 1.5x and 2x modes, the switches alternatively charge from the battery and discharge into the output. For G = 1.5x, the capacitors are charged from VIN in series and are discharged to VOUT in parallel. For G = 2x, the capacitors are charged from VIN EXIT STANDBY STARTUP: CHARGE VIN TO VOUT in parallel and are discharged to VOUT in parallel. In certain fault modes, the switches are opened and the output is physically isolated from the input. Automatic Gain Selection Each LED that is driven requires a current source. The voltage on this current source must be greater than a minimum headroom voltage (200 mV typical) to maintain accurate current regulation. The gain is automatically selected based on the minimum voltage (VDX) at all of the current sources. At startup, the device is placed into G = 1x mode and the output charges to VIN. If any VDX level is less than the required headroom (200 mV), the gain is increased to the next step (G = 1.5x). A 100 s delay is allowed for the output to stabilize prior to the next gain switching decision. If there remains insufficient current sink headroom, then the gain is increased again to 2x. Conversely, to optimize efficiency, it is not desirable for the output voltage to be too high. Therefore, the gain reduces when the headroom voltage is great enough. This point (labeled VDMAX in Figure 26) is internally calculated to ensure that the lower gain still results in ample headroom for all the current sinks. The entire cycle is illustrated in Figure 26. Note that the gain selection criteria apply only to active current sources. If current sources have been deactivated through an I2C command (for example, only five LEDs are used), then the voltages on the deactivated current sources are ignored. STANDBY 0 EXIT STARTUP 1 VOU T > VOUT(START) 0 G=1 WAIT 100s (TYP) MIN (VD1:D7) < VHR(UP) 1 1 G = 1.5 WAIT 100s (TYP) MIN (VD1:D7) < VHR(UP) 0 0 MIN (VD1:D7) > VDMAX 1 0 1 G=2 WAIT 100s (TYP) MIN (VD1:D7) < VDMAX NOTES 1. VDMAX IS THE CALCULATED GAIN DOWN TRANSITION POINT. Figure 26. State Diagram for Automatic Gain Selection Rev. 0 | Page 12 of 48 08392-025 ADP8863 Soft Start Feature At startup (either from UVLO activation or fault/standby recovery), the output is first charged by ISS (3.75 mA typical) until it reaches about 92% of VIN. This soft start feature reduces the inrush current that is otherwise present when the output capacitance is initially charged to VIN. When this point is reached, the controller enters G = 1x mode. If the output voltage is not sufficient, then the automatic gain selection determines the optimal point as defined in the Automatic Gain Selection section. Shutdown Mode Shutdown mode disables all circuitry, including the I2C receivers. Shutdown occurs when VIN is below the undervoltage thresholds. When VIN rises above VIN(START) (2.05 V typical), all registers are reset and the part is placed into standby mode. Reset Mode In reset mode, all registers are set to their default values and the part is placed into standby. There are two ways to reset the part: by power-on reset (POR) or using the nRST pin. POR is activated any time that the part exits shutdown mode. After a POR sequence is complete, the part automatically enters standby mode. After startup, the part can be reset by pulling the nRST pin low. As long as the nRST pin is low, the part is held in a standby state, but no I2C commands are acknowledged (all registers are kept at their default values). After releasing the nRST pin, all registers remain at their default values, and the part remains in standby; however, the part does accept I2C commands. The nRST pin has a 50 s (typical) noise filter to prevent inadvertent activation of the reset function. The nRST pin must be held low for this entire time to activate reset. The operating modes function according to the timing diagram in Figure 27. OPERATING MODES There are four different operating modes: active, standby, shutdown, and reset. Active Mode In active mode, all circuits are powered up and in a fully operational state. This mode is entered when Bit nSTBY (in Register MDCR) is set to 1. Standby Mode Standby mode disables all circuitry except for the I2C receivers. Current consumption is reduced to less than 1 A. This mode is entered when the nSTBY bit is set to 0 or when the nRST pin is held low for more than 100 s (maximum). When standby is exited, a soft start sequence is performed. SHUTDOWN VIN VIN CROSSES ~2.05V AND TRIGGERS POWER-ON RESET nRST MUST BE HIGH FOR 20s (MAX) BEFORE SENDING I2C COMMANDS BIT nSTBY IN REGISTER MDCR GOES LOW STANDBY ~100s DELAY BETWEEN POWER-UP AND WHEN I2C COMMANDS CAN BE RECEIVED 25s TO 100s NOISE FILTER nRST 2x GAIN CHANGES OCCUR ONLY WHEN NECESSARY, BUT HAVE A MIN TIME BEFORE CHANGING nRST IS LOW, WHICH FORCES STANDBY LOW AND RESETS ALL I2C REGISTERS VOUT VIN ~3.75mA CHARGES VOUT TO VIN LEVEL 1.5x 1x SOFT START 10s 100s SOFT START Figure 27. Typical Timing Diagram Rev. 0 | Page 13 of 48 08392-026 ADP8863 LED GROUPINGS Each LED can respond individually or be grouped together into the backlight controls. By default, all LEDs are set to be part of the backlight. This is changed by setting Bits[6:0] in Register 0x05. LEDs that are set up as independent sinks can be enabled individually in Register 0x10. They can also all be enabled simultaneously via the SIS_EN bit in Register 0x01. Any LEDs configured for the backlight can only be enabled via the BL_EN bit in Register 0x01. 30 25 LED CURRENT (mA) 20 15 LINEAR 10 SQUARE 5 LED CURRENT SETTINGS Any of the LED outputs (Pin D1 to Pin D7) can be used to drive any color of LED at 0 mA to 30 mA, provided that the LED's Vf is less than 4.1 V. Additionally, the D7 sink can regulate up to 60 mA. The current settings are determined by a 7-bit code programmed by the user into Register 0x14 through Register 0x1A (for the independent sinks) and Register 0x09 to Register 0x0E (for the backlight sinks). The 7-bit resolution allows the user to set the LED to one of 128 different levels. The ADP8863 can implement two distinct algorithms to achieve a linear or a nonlinear relationship between input code and diode output current. The law and SC_LAW bits in Register 0x04 and Register 0x0F, respectively, are used to change between these algorithms. By default, the ADP8863 uses a linear algorithm (law and SC_LAW = 00), where the LED current increases linearly for a corresponding increase in input code. LED current (in milliamperes) is determined by the following equation: LED Current (mA) = Code x (Full-Scale Current/127) where: Code is the input code programmed by the user. Full-Scale Current is the maximum sink current allowed per LED (typically 30 mA). The ADP8863 can also implement a nonlinear (square approximation) relationship between input code and LED current. In this case (law and SC_LAW = 01, 10, or 11), the LED current (in milliamperes) is determined by the following equation: (2) 0 32 64 CODE 96 128 Figure 28. LED Current vs. Input Code AUTOMATED FADE IN AND FADE OUT The LED drivers are easily configured for automated fade in and fade out. Sixteen fade in and fade out rates can be selected via the I2C interface. Fade in and fade out rates range from 0.0 sec to 5.5 sec (per full-scale current, either 30 mA or 60 mA). The backlight LEDs have separate fade in and fade out time controls from the independent sink LEDs. Table 5. Available Fade In and Fade Out Rates Code 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Fade Rate (in sec per Full-Scale Current) 0.0 (disabled) 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.5 4.0 4.5 5.0 5.5 Full - Scale Current LED Current (mA) = Code x 127 2 (3) Figure 28 shows the LED current level vs. input code for both the linear and square law algorithms. The fade profile is based on the transfer law selected (linear, square, Cubic 10, or Cubic 11) and the delta between the actual current and the target current. Smaller changes in current reduce the fade time. For linear and square law fades, the fade time is given by Fade Time = Fade Rate x (Code/127) where the Fade Rate is shown in Table 5. (4) Rev. 0 | Page 14 of 48 08392-027 0 ADP8863 The Cubic 10 and Cubic 11 laws also use the square law LED currents derived from Equation 3; however, the time between each step is varied to produce a steeper slope at higher currents and a shallower slope at lower currents (see Figure 29). 30 ISCx ON TIME FADE-IN MAX FADE-OUT FADE-IN ON TIME FADE-OUT 25 LINEAR CURRENT (mA) 20 OFF TIME OFF TIME SQUARE 10 CUBIC 11 5 CUBIC 10 0 0.25 0.50 UNIT FADE TIME 0.75 1.00 08392-028 SET BY USER Figure 30. Independent Sink Blink Mode with Fading RGB COLOR GENERATION The ADP8863 is easily programmed to generate any color with an RGB LED. To configure this feature, connect each LED in a standard RGB diode to a separate driver on the ADP8863. Because each channel can be programmed for a different current level, setting the currents for all three LEDs generates the desired color. To set the current levels, use a simple RGB color selector (see Figure 31). 0 Figure 29. Comparison of the Dimming Transfers Laws Each LED can be enabled independently and has its own current level, but all LEDs share the same fade in rates, fade out rates, and fade law. INDEPENDENT SINK CONTROL Each of the seven LEDs can be configured (in Register 0x05) to operate as either part of the backlight or to operate as an independent sink current (ISC). Each ISC can be enabled independently and has its own current level. All ISCs share the same fade in rates, fade out rates, and fade law. The ISCs have additional timers to facilitate blinking functions. A shared on timer (SCON) in conjunction with the off timer of each ISC (SC1OFF, SC2OFF, SC3OFF, SC4OFF, SC5OFF, SC6OFF, and SC7OFF) allows the LED current sinks to be configured in various blinking modes. The on timer can be set to one of four different settings: 0.2 sec, 0.6 sec, 0.8 sec, or 1.2 sec. The off timers have four different settings: disabled, 0.6 sec, 1.2 sec, and 1.8 sec. Blink mode is activated by setting the off timers to any setting other than disabled. Program all fade, on, and off timers before enabling any of the LED current sinks. If ISCx is on during a blink cycle and SCx_EN is cleared, the LED turns off (or fades to off if fade out is enabled). If ISCx is off during a blink cycle and SCx_EN is cleared, it stays off. Figure 31. Standard RGB Color Generator The example in Figure 31 shows a color of green, which is generated with a red content of 18 (out of 255), a green content of 190, and a blue content of 96. All numbers are out of a maximum of 255. Thus, the percentage of red is 7.1%, the percentage of green is 74.5%, and the percentage of blue is 37.6%. To generate the color with the ADP8863, scale this value to each of the current drivers. AUTOMATED RGB COLOR FADES The ADP8863 is easily programmed to cycle through RGB generated colors. This can be either a repeating or a random pattern of one color fading into the other. To execute this cycle autonomously, set up the RGB LEDs as described in the RGB Color Generation section and program the on, off, fading times, and current intensities. Adjusting the fading time in particular can create any pattern from a fast, striking effect to a soothing slow color change. Rev. 0 | Page 15 of 48 08392-036 08392-029 15 SCx_EN ADP8863 BACKLIGHT OPERATING LEVELS Backlight brightness control operates at three distinct levels: daylight (L1), office (L2), and dark (L3). The BLV bits in Register 0x04 control the specific level at which the backlight operates. These bits can be changed manually or, if in automatic mode (CMP_AUTOEN is set high in Register 0x01), by the ambient light sensor (see the Ambient Light Sensing section). By default, the backlight operates at daylight level (BLV = 00), where the maximum brightness is set using Register 0x09 (BLMX1). A daylight dim setting can also be set using Register 0x0A (BLDM1). When operating at office level (BLV = 01), the backlight maximum and dim brightness settings are set using Register 0x0B (BLMX2) and Register 0x0C (BLDM2). When operating at the dark level (BLV = 10), the backlight maximum and dim brightness settings are set using Register 0x0D (BLMX3) and Register 0x0E (BLDM3). 30mA DAYLIGHT (L1) OFFICE (L2) DARK (L3) BACKLIGHT CURRENT MAX DIM BL_EN = 1 DIM_EN = 1 DIM_EN = 0 BL_EN = 0 Figure 34. Backlight Turn On/Dim/Turn Off The maximum and dim settings can be set from 0 mA to 30 mA; therefore, it is possible to program a dim setting that is greater than a maximum setting. For normal expected operation, ensure that the dim setting is programmed to be less than the maximum setting. DAYLIGHT_MAX AUTOMATIC DIM AND TURN OFF TIMERS OFFICE_MAX DARK_MAX BACKLIGHT CURRENT DAYLIGHT_DIM OFFICE_DIM DARK_DIM 08392-037 0 BACKLIGHT OPERATING LEVELS The user can program the backlight to dim automatically by using the DIMT bits in Register 0x07. The dim timer has 127 settings ranging from 1 sec to 127 sec. Program the dim timer (DIMT) before turning on the backlight. If BL_EN = 1, the backlight turns on to its maximum setting and the dim timer starts counting. When the dim timer expires, the internal state machine sets DIM_EN = 1, and the backlight enters its dim setting. BACKLIGHT CURRENT DIM TIMER RUNNING DIM TIMER RUNNING Figure 32. Backlight Operating Levels BACKLIGHT TURN ON/TURN OFF/DIM With the device in active mode (nSTBY = 1), the backlight can be turned on using the BL_EN bit in Register 0x01. Before turning on the backlight, select the level (daylight (L1), office (L2), or dark (L3)) to operate in and ensure that maximum and dim settings are programmed for that level. The backlight turns on when BL_EN = 1. The backlight turns off when BL_EN = 0. BACKLIGHT CURRENT MAX DIM MAX BL_EN = 1 DIM_EN = 1 DIM_EN = 0 DIM_EN = 1 BL_EN = 0 08392-040 SET BY USER SET BY INTERNAL STATEMACHINE Figure 35. Dim Timer BL_EN = 1 BL_EN = 0 Figure 33. Backlight Turn On/Turn Off If the user clears the DIM_EN bit, the backlight reverts to its maximum setting and the dim timer begins counting again. When the dim timer expires, the internal state machine again sets DIM_EN = 1, and the backlight enters its dim setting. The backlight can be turned off at any point during the dim timer countdown by clearing BL_EN. The user can also program the backlight to turn off automatically by using the OFFT bits in Register 0x06. The off timer has 127 settings ranging from 1 sec to 127 sec. Program the off timer (OFFT) before turning on the backlight. If BL_EN = 1, the backlight turns on to its maximum setting and the off timer While the backlight is on (BL_EN = 1), the user can change to the dim setting by programming DIM_EN = 1 in Register 0x01. If DIM_EN = 0, the backlight reverts to its maximum setting. 08392-038 Rev. 0 | Page 16 of 48 08392-039 ADP8863 starts counting. When the off timer expires, the internal state machine clears the BL_EN bit, and the backlight turns off. BACKLIGHT CURRENT OFF TIMER RUNNING BACKLIGHT CURRENT FADE-IN OVERRIDDEN FADE-OUT OVERRIDDEN MAX MAX BL_EN = 1 BL_EN = 1 (REASSERTED) BL_EN = 0 BL_EN = 0 BL_EN = 1 08392-041 BL_EN = 1 BL_EN = 0 SET BY USER SET BY INTERNAL STATE MACHINE Figure 38. Fade Override Function (FOVR Is High) AMBIENT LIGHT SENSING The ADP8863 integrates two ambient light sensing comparators. One of the ambient light sensing comparator pins (CMP_IN) is always available. The second pin (D6) has an ambient light sensor comparator (CMP_IN2) that can be activated rather than connecting an LED to D6. Activating the CMP_IN2 function of the pin is accomplished through the CMP2_SEL bit in Register CFGR. Therefore, when the CMP2_ SEL bit is set to 0, Pin D6 is programmed as a current sink. When the CMP2_SEL bit is set to 1, Pin D6 becomes the input for a second phototransistor. These comparators have two programmable trip points (L2 and L3) that select one of the three backlight operation modes (daylight, office, and dark) based on the ambient lighting conditions. Figure 36. Off Timer The backlight can be turned off at any point during the off timer countdown by clearing BL_EN. The dim timer and off timer can be used together for sequential maximum-to-dim-to-off functionality. With both the dim and off timers programmed, and BL_EN asserted, the backlight turns on to its maximum setting, and when the dim timer expires, the backlight changes to its dim setting. When the off timer expires, the backlight turns off. BACKLIGHT CURRENT DIM TIMER RUNNING MAX OFF TIMER RUNNING DIM The L3 comparator controls the dark-to-office mode transition. The L2 comparator controls the office-to-daylight transition (see Figure 39). The currents for the different lighting modes are defined in the BLMXx and BLDMx registers (see the Backlight Operating Levels Section). 08392-042 BL_EN = 1 DIM_EN = 1 BL_EN = 0 SET BY USER SET BY INTERNAL STATE MACHINE L2_OUT = 1 L3_OUT = 1 L2_OUT = 1 L3_OUT = 0 L2_OUT = 0 L3_OUT = 0 Figure 37. Dim and Off Timers Used Together 0 LUX FADE OVERRIDE A fade override feature (FOVR in Register CFGR (0x04)) enables the host to override the preprogrammed fade in or fade out settings. If FOVR is set and the backlight is enabled in the middle of a fade out process, the backlight instantly (within approximately 100 ms) returns to its maximum setting. Alternatively, if the backlight is fading in, reasserting BL_EN overrides the programmed fade in time, and the backlight instantly goes to its final fade value. This is useful for situations in which a key is pressed during a fade sequence. However, if FOVR is cleared and the backlight is enabled in the middle of a fade process, the backlight gradually brightens from where it was interrupted (it does not go down to 0 and then comes back on). 0A DARK OFFICE DAYLIGHT BRIGHTNESS Figure 39. Light Sensor Modes Based on the Detected Ambient Light Level Each light sensor comparator uses an external capacitor together with an internal reference current source to form an analog-todigital converter (ADC) that samples the output of the external photosensor. The ADC result is fed into two programmable trip comparators. The ADC has an input range of 0 A to 1080 A (typical). Rev. 0 | Page 17 of 48 08392-044 L3 L2 08392-043 ADP8863 L2_EN L2_TRIP L2_HYS L2_OUT ware may select the comparator of the phototransistor that is exposed to higher light intensity to control the transition between the programmed backlight intensity levels. The L2_CMPR and L3_CMPR comparators can be enabled independently of each other, or they can operate simultaneously. A single conversion from each ADC takes 80 ms (typical). When CMP_AUTOEN is set for automatic backlight adjustment (see the Automatic Backlight Adjustment section), the ADC and comparators run continuously. If the backlight is disabled and at least one independent sink is enabled, it is possible to use the light sensor comparators in a single-shot mode. A single-shot read of the photocomparators is performed by setting the FORCE_RD bit in Register 0x1B. After the single-shot measurement is completed, the internal state machine clears the FORCE_RD bit. The interrupt flags (CMP_INT and CMP_INT2) can be used to notify the system when either L2 or L3 changes state. See the Interrupts section for more information. PHOTO SENSOR OUTPUT FILTER SETTINGS ADC L3_TRIP L3_HYS L3_OUT L3_EN Figure 40. Ambient Light Sensing and Trip Comparators The L2 comparator, L2_CMPR, detects when the photosensor output has dropped below the programmable L2_TRP point (Register 0x1D). If this event occurs, then the L2_OUT status signal is set. L2_CMPR contains programmable hysteresis, meaning that the photosensor output must rise above L2_TRP + L2_HYS before L2_OUT clears. L2_CMPR is enabled via the L2_EN bit. The L2_TRP and L2_HYS values of L2_CMPR can be set between 0 A and 1080 A (typical) in steps of 4.3 A (typical). The L3 comparator, L3_CMPR, detects when the photosensor output drops below the programmable L3_TRP point (Register 0x1F). If this event occurs, the L3_OUT status signal is set. L3_CMPR contains programmable hysteresis, meaning that the photosensor output must rise above L3_TRP + L3_HYS before L3_OUT clears. L3_CMPR is enabled via the L3_EN bit. The L3_TRP and L3_HYS values of L3_CMPR can be set between 0 A and 137.7 A (typical) in steps of 0.54 A (typical). L2_TRP L2_HYS 08392-045 AUTOMATIC BACKLIGHT ADJUSTMENT The ambient light sensor comparators can automatically transition the backlight between one of its three operating levels. To enable this mode, set the CMP_AUTOEN bit in Register 0x01. When I2C selection is enabled, the internal state machine takes control of the BLV bits and changes them based on the L2_OUT and L3_OUT status bits. When L2_OUT is set high, it indicates that the ambient light conditions have dropped below the L2_TRP point and that the backlight should move to its office (L2) level. When L3_OUT is set high, it indicates that ambient light conditions have dropped below the L3_TRP point and that the backlight should move to its dark (L3) level. Table 6 shows the relationship between backlight operation and the ambient light sensor comparator outputs. The L3_OUT status bit has greater priority; therefore, if L3_OUT is set, the backlight operates at L3 (dark) even if L2_OUT is also set. Filter times from 80 ms to 10 sec can be programmed for the comparators (Register 0x1B and Register 0x1C) before they change state. Table 6. Comparator Output Truth Table CMP_AUTOEN 0 1 1 1 1 L3_TRP L3_HYS 1 10 ADC RANGE (A) 100 1000 Figure 41. Comparator Ranges 08392-046 Note that the full-scale value of the L2_TRP and L2_HYS registers is 250 (decimal). Therefore, if the value of L2_TRP + L2_HYS exceeds 250, the comparator output is unable to deassert. For example, if L2_TRP is set to 204 (80% of the fullscale value, or approximately 0.80 x 1080 A = 864 A), then L2_HYS must be set to less than 46 (250 - 204 = 46). If it is not, then L2_HYS + L2_TRP exceeds 250 and the L2_CMPR comparator is never allowed to go low. When both phototransistors are enabled and programmed in automatic mode (through Bit CMP_AUTOEN in Register 0x01), the user application must determine which comparator outputs to use, by selecting Bit SEL_AB in Register 0x04 for automatic light sensing transitions. For example, the user soft- L3_OUT X1 0 0 1 L2_OUT X1 0 1 X1 Backlight Operation BLV can be manually set by the user BLV = 00, backlight operates at L1 (daylight) BLV = 01, backlight operates at L2 (office) BLV = 10, backlight operates at L3 (dark) X is the don't care bit. Rev. 0 | Page 18 of 48 ADP8863 USING THE ADP8863 TO DRIVE ADDITIONAL LEDS In some situations, it may be desirable to drive more than seven LEDs. This can be done in one of two ways: paralleling LEDs using ballast resistors, or using the ADP8863 to power additional LED drivers. Ballast Resistors In the first method, multiple LEDs can be attached to any one LED driver with the use of ballast resistors. I1 + Vf1 - VOUT I2 I3 + Vf3 - RBALLAST nRST VDDIO VIN 1F VDDIO D1 D2 D3 D4 D5 D6 D7 VOUT 1F + Vf2 - RBALLAST C1+ RBALLAST VDX ADP8863 SDA VDDIO 08392-033 C1- C2+ C2- C1 1F IDX = I1 + I2 + I3 SCL VDDIO nINT GND1 GND2 C2 1F Figure 42. Ballast Resistor Arrangement Ballast resistors attempt to compensate for the forward voltage (Vf) mismatch inherent in any parallel combination of LEDs. The choice of a ballasting resistor is a trade-off between the efficiency and the current matching of the LEDs in parallel. Smaller ballast resistors give better efficiency. Larger ballast resistors gives better current matching, because the resistor balances out the current differences for a voltage drop. The relationship is summarized with the following: R BALLAST Vf I Figure 43. Powering Additional LEDs with Ballast Resistors Adding Additional Parallel Sinks The ballast resistor's compromises of efficiency and matching are not suitable for many applications. Therefore, another option is to use the ADP8863 charge pump to power additional current sinks. First, the charge pump must be optimized for this option by setting the GDWN_DIS bit in Register 0x01, which prevents the charge pump from switching back down in gain, and thus stabilizes it against the unknown loads that the additional current sinks present. To use the sinks, turn the ADP8863 charge pump on before activating the additional sinks. If the additional sinks are activated first, the ADP8863 soft start may not complete. The ADP8863 can be set up with an ADP8860 or ADP8861. An example using the ADP8861 is shown in Figure 44. (5) where: Vf is the difference between the maximum Vf and the minimum Vf of the LEDs in parallel. I is the difference between the parallel LED currents. The addition of the ballast resistor brings the effective Vf of the LED to Vf (eff ) = Vf (LED ) + I LED x R BALLAST (6) The ILED x RBALLAST term forces the charge pump to work a little harder for this additional voltage drop. Furthermore, for guaranteed operation with the ADP8863, the total Vf(eff) should never exceed VOUT(REG) - VHR(UP) (see Table 1). Rev. 0 | Page 19 of 48 08392-034 ADP8863 BACKLIGHT KEYPAD OR FUN LIGHTING VIN 1F VALS PHOTO SENSOR CMP_IN nRST SDA SCL nINT 0.1F D2 D3 D4 D5 D6 D7 D1 VOUT 1F VIN 1F nRST D2 D3 D4 D5 D6 D7 D1 VOUT C1+ C1- C2+ C2- NC NC NC NC ADP8861 ADP8863 C1+ C1- C2+ C2- C2 1F C1 1F SDA SCL nINT GNDx GNDx Figure 44. Connecting the ADP8863 to an ADP8861 to Power More LEDs OPERATING LEDS FROM ALTERNATIVE SUPPLIES For some applications, it is advantageous to operate the LEDs from a voltage source other than the ADP8863 charge pump output. For example, it may be possible to operate a red LED over the entire battery voltage range without any charge pump boosting. For a charge pump, I IN = Gain x I OUT D1 VIN 1F VDDIO nRST VDDIO VOUT 1F D2 D3 D4 D5 D6 D7 (7) C1+ Therefore, operating the red LEDs directly from the battery removes output current of the red LEDs from the charge pump draw. This in turn reduces the total input current by (Gain - 1) x IOUT(red). However, care must be taken when selecting LEDs to operate from a different voltage input. Specifically, the voltage source must at least be able to support the maximum forward voltage (Vf) of the LED plus the maximum VHR(UP) (276 mV, given in Table 1). Additionally, operating an LED from an independent voltage source may interfere with the ADP8863's gain selection algorithm. This algorithm selects the optimal gain for the charge pump based on all seven diodes. By operating one or more of the diodes from another supply, the algorithm may not switch the gain back down to a lower state until the LEDs are disabled or the part enters standby. 08392-047 ADP8863 SDA VDDIO SCL VDDIO nINT GND1 GND2 C1- C2+ C2- C1 1F C2 1F Figure 45. Alternate Schematic for Low Vf LEDs Rev. 0 | Page 20 of 48 08392-030 ADP8863 SHORT-CIRCUIT PROTECTION MODE The ADP8863 can protect against short circuits on the output (VOUT). Short-circuit protection (SCP) is activated at the point when VOUT < 55% of VIN. Note that SCP sensing is disabled during both startup and restart attempts (fault recovery). SCP sensing is reenabled 4 ms (typical) after activation. During a short-circuit fault, the device enters a low current consumption state and an interrupt flag is set. The device can be restarted at any time after receiving a short-circuit fault by rewriting nSTBY = 1. It then repeats another complete soft start sequence. Note that the value of the output capacitance (COUT) should be small enough to allow VOUT to reach approximately 55% (typical) of VIN within the 4 ms (typical) time. If COUT is too large, the device inadvertently enters short-circuit protection. current sources and all other device functionality remain intact. When the output voltage falls by about 500 mV (to 5.3 V typical), the charge pump resumes operation. If the fault or load event recurs, the process may repeat. An interrupt flag is set at each OVP instance. THERMAL SHUTDOWN/OVERTEMPERATURE PROTECTION If the die temperature of the ADP8863 rises above a safe limit (150C typical), the controllers enter thermal shutdown (TSD) protection mode. In this mode, most of the internal functions shut down, the part enters standby, and the TSD_INT interrupt (Register 0x02) is set. When the die temperature decreases below ~130C, the part can be restarted. To restart the part, remove it from standby. No interrupt is generated when the die temperature falls below 130C. However, if the software clears the pending TSD_INT interrupt and the temperature remains above 130C, another interrupt is generated. The complete state machine for these faults (SCP, OVP, and TSD) is shown in Figure 46. OVERVOLTAGE PROTECTION Overvoltage protection (OVP) is implemented on the output. There are two types of overvoltage events: normal (no fault) and abnormal (from a fault or sudden load change). Normal Overvoltage In a normal (no fault) overvoltage, the output voltage approaches VOUT(REG) (4.9 V typical) during normal operation. This is not caused by a fault or load change, but is simply a consequence of the input voltage times the gain reaching the same level as the clamped output voltage (VOUT(REG)). To prevent this type of overvoltage, the ADP8863 detects when the output voltage rises to VOUT(REG). It then increases the effective ROUT of the gain stage to reduce the voltage that is delivered. This effectively regulates VOUT to VOUT(REG); however, there is a limit to the effect that this system can have on regulating VOUT. It is designed only for normal operation and it is not intended to protect against faults or sudden load changes. When the output voltage is regulated to VOUT(REG), no interrupt is set and the operation is transparent to the LEDs and the overall application. INTERRUPTS There are five interrupt sources available on the ADP8863 in Register 0x02. * * * * * Abnormal Overvoltage Because of the open-loop behavior of the charge pump as well as how the gain transitions are computed, a sudden load change or fault can abnormally force VOUT beyond 6 V. This causes an abnormal overvoltage situation. If the event happens slowly enough, the system first tries to regulate the output to 4.9 V as in a normal overvoltage scenario. However, if this is not sufficient, or if the event happens too quickly, the ADP8863 enters overvoltage protection (OVP) mode when VOUT exceeds the OVP threshold (typically 5.8 V). In OVP mode, only the charge pump is disabled to prevent VOUT from rising too high. The Main light sensor comparator: The CMP_INT interrupt sets every time the main light sensor comparator detects a threshold (L2 or L3) transition (rising or falling condition). Sensor Comparator 2: The CMP2_INT interrupt works the same way as CMP_INT, except that the sensing input derives from the second light sensor. The programmable thresh-olds are the same as for the main light sensor comparator. Overvoltage protection: OVP_INT is generated when the output voltage exceeds 5.8 V (typical). Thermal shutdown circuit: an interrupt (TSD_INT) is generated when entering overtemperature protection. Short-circuit detection: SHORT_INT is generated when the device enters short-circuit protection mode. The interrupt (if any) that appears on the nINT pin is determined by the bits mapped in Register INTR_EN (0x03). To clear an interrupt, write a 1 to the interrupt in the MDCR2 register (0x02) or reset the part. Reading the interrupt, or writing a 0, has no effect. Rev. 0 | Page 21 of 48 ADP8863 STANDBY EXIT STANDBY 0 1 DIE TEMP > TSD EXIT STBY 1 0 TSD FAULT STARTUP: CHARGE VIN TO VOUT 0 SCP FAULT DIE TEMP < TSD - TSD(HYS) VOUT > VOUT(START) 1 0 EXIT STARTUP VOUT < VOUT(SC) 0 1 0 G=1 WAIT 100s (TYP) MIN (VD1:D7) < VHR(UP) VOUT < VOVP - VOVP(HYS) 0 VOUT > VOVP 1 OVP FAULT 1 1 1 VOUT < VOVP - VOVP(HYS) 0 G = 1.5 WAIT 100s (TYP) MIN (VD1:D7) < VHR(UP) 0 0 MIN (VD1:D7) > VDMAX 0 VOUT > VOUT(REG) OVP FAULT 1 TRY TO REGULATE VOUT TO VOUT(REG) 0 1 1 1 VOUT > VOVP 0 1 VOUT < VOVP - VOVP(HYS) 0 G=2 WAIT 100s (TYP) MIN (VD1:D7 ) > VDMAX 0 VOUT > VOUT(REG) OVP FAULT 1 TRY TO REGULATE VOUT TO VOUT(REG) 0 1 NOTES 1. VDMAX IS THE CALCULATED GAIN DOWN TRANSITION POINT. 08392-031 VOUT > VOVP Figure 46. Fault State Machine Rev. 0 | Page 22 of 48 ADP8863 APPLICATIONS INFORMATION The ADP8863 allows the charge pump to operate efficiently with a minimum of external components. Specifically, the user must select an input capacitor (CIN), output capacitor (COUT), and two charge pump fly capacitors (C1 and C2). CIN should be 1 F or greater. The value must be high enough to produce a stable input voltage signal at the minimum input voltage and maximum output load. A 1 F capacitor for COUT is recommended. Larger values are permissible, but care must be exercised to ensure that VOUT charges above 55% (typical) of VIN within 4 ms (typical). See the Short-Circuit Protection Mode section for more details. For best practice, it is recommended that the two charge pump fly capacitors be 1 F; larger values are not recommended, and smaller values may reduce the ability of the charge pump to deliver maximum current. For optimal efficiency, the charge pump fly capacitors should have low equivalent series resistance (ESR). Low ESR X5R or X7R capacitors are recommended for all four components. The use of fly capacitors sized 0402 and smaller is allowed, but the GDWN_DIS bit in Register 0x01 must be set. Minimum voltage ratings should adhere to the guidelines in Table 7. Table 7. Capacitor Stress in Each Charge Pump Gain State Capacitor CIN COUT C1 C2 Gain = 1x VIN VIN None None Gain = 1.5x VIN VIN x 1.5 (max of 5.5 V) VIN/2 VIN/2 Gain = 2x VIN VIN x 2.0 (max of 5.5 V) VIN VIN voltage drop across the regulating current source. This gives VOUT = Vf(MAX) + VDX (9) Combining Equation 8 and Equation 9 gives VIN = (Vf(MAX) + VDX + IOUT x ROUT(G))/G (10) Equation 10 is useful for calculating approximate bounds for the charge pump design. Determining the Transition Point of the Charge Pump Consider the following design example, where: Vf(MAX) = 3.7 V IOUT = 140 mA (7 LEDs at 20 mA each) ROUT(G = 1.5x) = 3 (obtained from Figure 12) At the point of a gain transition, VDX = VHR(UP). Table 1 gives the typical value of VHR(UP) as 0.2 V. Therefore, the input voltage level when the gain transitions from 1.5x to 2x is VIN = (3.7 V + 0.2 V + 140 mA x 3 )/1.5 = 2.88 V LAYOUT GUIDELINES Note the following layout guidelines: * For optimal noise immunity, place the CIN and COUT capacitors as close as possible to their respective pins. These capacitors should share a short ground trace. If the LEDs are a significant distance from the VOUT pin, another capacitor on VOUT, placed closer to the LEDs, is advisable. * For optimal efficiency, place the charge pump fly capacitors (C1 and C2) as close to the part as possible. * The ADP8863 does not distinguish between power ground and analog ground. Therefore, both ground pins can be connected directly together. It is recommended that these ground pins be connected at the ground for the input and output capacitors. * The LFCSP package requires the exposed pad to be soldered at the board to the GND1 and/or GND2 pin(s). * Unused diode pins (Pin D1 to Pin D7) can be connected to ground or to VOUT, or remain floating. However, the unused diode current sinks must be disabled by setting them as independent sinks in Register 0x05 and then disabling them in Register 0x10. If they are not disabled, the charge pump efficiency may suffer. * If the CMP_IN phototransistor input is not used, it can be connected to ground or remain floating. * If the interrupt pin (nINT) is not used, connect it to ground or leave it floating. Never connect it to a voltage supply, except through a 1 k series resistor. * The ADP8863 has an integrated noise filter on the nRST pin. Under normal conditions, it is not necessary to filter the reset line. However, if the part is exposed to an unusually noisy signal, it is beneficial to add a small RC filter or bypass capacitor on this pin. If the nRST pin is not used, it must be pulled well above the VIH(MIN) level (see Table 1). Do not allow the nRST pin to float. If one or both ambient light sensor comparator inputs (CMP_IN and D6) are used, a small capacitor (0.1 F is recommended) must be connected from the input to ground. Any color LED can be used if the Vf (forward voltage) is less than 4.1 V. However, using lower Vf LEDs reduces the input power consumption by allowing the charge pump to operate at lower gain states. The equivalent circuit model for a charge pump is shown in Figure 47. VOUT ROUT G x VIN IOUT COUT VDX 08392-032 Figure 47. Charge Pump Equivalent Circuit Model The input voltage is multiplied by the gain (G) and delivered to the output through an effective resistance (ROUT). The output current flows through ROUT and produces an IR drop to yield VOUT = G xVIN - IOUT x ROUT(G) (8) The ROUT term is a combination of the RDSON resistance for the switches used in the charge pump and a small resistance that accounts for the effective dynamic charge pump resistance. The ROUT level changes based upon the gain (the configuration of the switches). Typical ROUT values are given in Table 1, Figure 12, and Figure 13. VOUT is also equal to the largest Vf of the LEDs used plus the Rev. 0 | Page 23 of 48 ADP8863 I2C PROGRAMMING AND DIGITAL CONTROL The ADP8863 provides full software programmability to facilitate its adoption in various product architectures. The I2C address is 0101011x (x = 0 during write, x = 1 during read). Therefore, the write address is 0x56 and the read address is 0x57. Note the following general behavior of registers: * * * Table 8 to Table 84 provide register and bit descriptions. The reset value for all bits in the bit map tables is all 0s, except in Table 10 (see Table 10 for its unique reset value). Wherever the acronym N/A appears in the tables, it means not applicable. All registers are set to their default values during reset or after a UVLO event. All registers are read/write unless otherwise specified. Unused bits are read as zero. B7 ST 0 1 0 1 0 1 1 B0 R/W ACK B7 REGISTER ADDRESS B0 ACK B7 REGISTER VALUE 8-BIT VALUE TO WRITE IN THE ADDRESSED REGISTER B0 ACK ST WRITE = 0 START FROM ADP8863 FROM ADP8863 DEVICE ID FOR WRITE OPERATION SELECT REGISTER TO WRITE FROM ADP8863 STOP B0 ACK ST SLAVE TO MASTER MASTER TO SLAVE Figure 48. I2C Write Sequence B7 ST 0 1 0 1 0 1 B0 1 R/W ACK B7 REGISTER ADDRESS B0 B7 ACK RS 0 1 0 1 0 1 B0 1 R/W ACK B7 REGISTER VALUE WRITE = 0 FROM MASTER 08392-048 START REPEATED START FROM ADP8863 FROM ADP8863 READ = 1 DEVICE ID FOR WRITE OPERATION SELECT REGISTER TO WRITE DEVICE ID FOR READ OPERATION FROM ADP8863 8-BIT VALUE TO WRITE IN THE ADDRESSED REGISTER STOP 08392-049 SLAVE TO MASTER MASTER TO SLAVE Figure 49. I2C Read Sequence Rev. 0 | Page 24 of 48 ADP8863 Table 8. Register Set Definitions Address (Hex) 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F 0x20 0x21 0x22 0x23 0x24 Register Name MFDVID MDCR MDCR2 INTR_EN CFGR BLSEN BLOFF BLDIM BLFR BLMX1 BLDM1 BLMX2 BLDM2 BLMX3 BLDM3 ISCFR ISCC ISCT1 ISCT2 ISCF ISC7 ISC6 ISC5 ISC4 ISC3 ISC2 ISC1 CCFG CCFG2 L2_TRP L2_HYS L3_TRP L3_HYS PH1LEVL PH1LEVH PH2LEVL PH2LEVH Description Manufacturer and device ID Device mode and status Device mode and Status Register 2 Interrupts enable Configuration register Sink enable, backlight or independent Backlight off timeout Backlight dim timeout Backlight fade in and fade out rates Backlight (brightness Level 1--daylight) maximum current Backlight (brightness Level 1--daylight) dim current Backlight (brightness Level 2--office) maximum current Backlight (brightness Level 2--office) dim current Backlight (brightness Level 3--dark) maximum current Backlight (brightness Level 3--dark) dim current Independent sink current fade control register Independent sink current control register Independent sink current timer register, LED[7:5] Independent sink current timer register, LED[4:1] Independent sink current fade register Independent sink current, LED7 Independent sink current, LED6 Independent sink current, LED5 Independent sink current, LED4 Independent sink current, LED3 Independent sink current, LED2 Independent sink current, LED1 Comparator configuration Second comparator configuration L2 comparator reference L2 hysteresis L3 comparator reference L3 hysteresis First phototransistor ambient light level--low byte register First phototransistor ambient light level--high byte register Second phototransistor ambient light level--low byte register Second phototransistor ambient light level--high byte register Rev. 0 | Page 25 of 48 ADP8863 Table 9. Register Map Addr (Hex) 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F 0x20 0x21 0x22 0x23 0x24 Reg. Name MFDVID MDCR MDCR2 INTR_EN CFGR BLSEN BLOFF BLDIM BLFR BLMX1 BLDM1 BLMX2 BLDM2 BLMX3 BLDM3 ISCFR ISCC ISCT1 ISCT2 ISCF ISC7 ISC6 ISC5 ISC4 ISC3 ISC2 ISC1 CCFG CCFG2 L2_TRP L2_HYS L3_TRP L3_HYS PH1LEVL PH1LEVH PH2LEVL PH2LEVH Bit 7 Reserved Bit 6 Bit 5 Manufacturer ID INT_CFG nSTBY Reserved Reserved SEL_AB CMP2_SEL D7EN D6EN Bit 4 DIM_EN SHORT_INT SHORT_IEN BLV D5EN D4EN OFFT DIMT BL1_MC BL1_DC BL2_MC BL2_DC BL3_MC BL3_DC SC6_EN Reserved SC5_EN SC7OFF SC3OFF SC4_EN SC3_EN SC6OFF SC2OFF SC2_EN SC_LAW SC1_EN SC5OFF SC1OFF Bit 3 GDWN_DIS TSD_INT TSD_IEN Bit 2 Bit 1 Device ID SIS_EN CMP_AUTOEN OVP_INT CMP2_INT OVP_IEN CMP2_IEN Law D3EN D2EN Bit 0 BL_EN CMP_INT CMP_IEN FOVR D1EN Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved BL_FO BL_FI Reserved SC7_EN SCON SC4OFF SCR Reserved Reserved Reserved Reserved Reserved Reserved FILT FILT2 SCFO SCD7 SCD6 SCD5 SCD4 SCD3 SCD2 SCD1 FORCE_RD L3_OUT FORCE_RD2 L3_OUT2 L2_TRP L2_HYS L3_TRP L3_HYS PH1LEV_LOW PH2LEV_LOW Reserved SCFI L2_OUT L2_OUT2 L3_EN L3_EN2 L2_EN L2_EN2 Reserved PH1LEV_HIGH PH2LEV_HIGH Rev. 0 | Page 26 of 48 ADP8863 Manufacturer and Device ID (MFDVID)--Register 0x00 This is a read-only register. Table 10. MFDVID Bit Map Bit 7 0 Bit 6 0 Bit 5 Manufacturer ID 1 Bit 4 0 Bit 3 1 Bit 2 0 Bit 1 Device ID 1 Bit 0 0 Mode Control Register (MDCR)--Register 0x01 Table 11. MDCR Bit Map Bit 7 Reserved Bit 6 INT_CFG Bit 5 nSTBY Bit 4 DIM_EN Bit 3 GDWN_DIS Bit 2 SIS_EN Bit 1 CMP_AUTOEN Bit 0 BL_EN Table 12. Bit Descriptions for the MDCR Register Bit Name N/A INT_CFG Bit No. 7 6 Description Reserved. Interrupt configuration. 1 = processor interrupt deasserts for 50 s and reasserts with pending events. 0 = processor interrupt remains asserted if the host tries to clear the interrupt while there is a pending event. 1 = device is in active mode. 0 = device is in standby mode; only the I2C interface is enabled. DIM_EN is set by the hardware after a dim timeout. The user may also force the backlight into dim mode by asserting this bit. Dim mode can only be entered if BL_EN is also enabled. 1 = backlight is operating at the dim current level (BL_EN must also be asserted). 0 = backlight is not in dim mode. Gain down disable bit. Setting this bit does not allow the charge pump to switch to lower gains. 1 = the charge pump does not switch down in gain until all LEDs are off. The charge pump switches up in gain as needed. This feature is useful if the ADP8863 charge pump is used to drive an external load. This feature must be used when utilizing small fly capacitors (0402 or smaller). 0 = the charge pump automatically switches up and down in gain. This provides optimal efficiency, but is not suitable for driving loads that are not connected through the ADP8863 diode drivers. Additionally, the charge pump fly capacitors should be low ESR and sized 0603 or greater. Synchronous independent sinks enable. 1 = enables all LED current sinks designated as independent sinks. All of the ISC enable bits must be cleared; if any of the SCx_EN bits in Register 0x10 are set, this bit has no effect. 0 = disables all sinks designated as independent sinks. All of the ISC enable bits must be cleared; if any of the SCx_EN bits in Register 0x10 are set, this bit has no effect. 1 = backlight automatically responds to the comparator outputs (L2_OUT and L3_OUT). L2_EN and/or L3_EN must be set for this to function. BLV values in Register 0x04 are overridden. 0 = backlight does not respond automatically to comparator level changes. The user can manually select backlight operating levels using Bit BLV in Register 0x04. 1 = backlight is enabled (nSTBY must also be asserted). 0 = backlight is disabled. nSTBY DIM_EN 5 4 GDWN_DIS 3 SIS_EN 2 CMP_AUTOEN 1 BL_EN 0 Rev. 0 | Page 27 of 48 ADP8863 Mode Control Register 2 (MDCR2)--Register 0x02 Table 13. MDCR2 Bit Map Bit 7 Bit 6 Reserved Bit 5 Bit 4 SHORT_INT Bit 3 TSD_INT Bit 2 OVP_INT Bit 1 CMP2_INT Bit 0 CMP_INT Table 14. Bit Descriptions for the MDCR2 Register Bit Name N/A SHORT_INT Bit No. [7:5] 4 Description 1 Reserved. Short-circuit error interrupt. 1 = a short-circuit or overload condition on VOUT has been detected. 0 = no short-circuit or overload condition has been detected. Thermal shutdown interrupt. 1 = the device temperature has exceeded 150C (typical). 0 = no overtemperature condition has been detected. Overvoltage interrupt. 1 = VOUT has exceeded VOVP. 0 = VOUT has not exceeded VOVP. 1 = the second ALS comparator (CMP_IN2) has changed state. 0 = the second sensor comparator has not been triggered. 1 = main ALS comparator (CMP_IN) has changed state. 0 = the main sensor comparator has not been triggered. TSD_INT 3 OVP_INT 2 CMP2_INT CMP_INT 1 0 1 Interrupt bits are cleared by writing a 1 to the flag; writing a 0 or reading the flag has no effect. Interrupt Enable (INTR_EN)--Register 0x03 Table 15. INTR_EN Bit Map Bit 7 Bit 6 Reserved Bit 5 Bit 4 SHORT_IEN Bit 3 TSD_IEN Bit 2 OVP_IEN Bit 1 CMP2_IEN Bit 0 CMP_IEN Table 16. Bit Descriptions for the INTR_EN Register Bit Name N/A SHORT_IEN Bit No. [7:5] 4 Description Reserved. Short-circuit interrupt is enabled. When the SHORT_INT status bit is set after an error condition, an interrupt is raised to the host if the SHORT_IEN flag is enabled. 1 = the short-circuit interrupt is enabled. 0 = the short-circuit interrupt is disabled (the SHORT_INT flag continues to assert). Thermal shutdown interrupt is enabled. When the TSD_INT status bit is set after an error condition, an interrupt is raised to the host if the TSD_IEN flag is enabled. 1 = the thermal shutdown interrupt is enabled. 0 = the thermal shutdown interrupt is disabled (the TSD_INT flag continues to assert). Overvoltage interrupt enabled. When the OVP_INT status bit is set after an error condition, an interrupt is raised to the host if the OVP_IEN flag is enabled. 1 = the overvoltage interrupt is enabled. 0 = the overvoltage interrupt is disabled (the OVP_INT flag continues to assert). When the CMP2_INT status bit is set after an enabled comparator trips, an interrupt is raised if the CMP2_IEN flag is enabled. 1 = the second phototransistor comparator interrupt is enabled. 0 = the second phototransistor comparator interrupt is disabled (the CMP2_INT flag continues to assert). When the CMP_INT status bit is set after an enabled comparator trips, an interrupt is raised if the CMP_IEN flag is enabled. 1 = the main comparator interrupt is enabled. 0 = the main comparator interrupt is disabled (the CMP_INT flag continues to assert). TSD_IEN 3 OVP_IEN 2 CMP2_IEN 1 CMP_IEN 0 Rev. 0 | Page 28 of 48 ADP8863 BACKLIGHT REGISTER DESCRIPTIONS Configuration Register (CFGR)--Register 0x04 Table 17. CFGR Bit Map Bit 7 Reserved Bit 6 SEL_AB Bit 5 CMP2_SEL Bit 4 Bit 3 BLV Bit 2 Bit 1 Law Bit 0 FOVR Table 18. Bit Descriptions for the CFGR Register Bit Name N/A SEL_AB CMP2_SEL BLV Bit No. 7 6 5 [4:3] Description Reserved. 1 = selects the second phototransistor (CMP_IN2) to control the backlight. 0 = selects the main phototransistor (CMP_IN) to control the backlight. 1 = the second phototransistor is enabled; the current sink on D6 is disabled. 0 = the second phototransistor is disabled. Brightness level. This field indicates the brightness level at which the device is operating. The software may force the backlight to operate at one of the three brightness levels. Setting CMP_AUTOEN high (Register 0x01) sets these values automatically and overwrites any previously written values. 00 = Level 1 (daylight). 01 = Level 2 (office). 10 = Level 3 (dark). 11 = off (backlight set to 0 mA). Backlight transfer law. 00 = linear law DAC, linear time steps. 01 = square law DAC, linear time steps. 10 = square law DAC, nonlinear time steps (Cubic 10). 11 = square law DAC, nonlinear time steps (Cubic 11). Backlight fade override. 1 = the backlight fade override is enabled. 0 = the backlight fade override is disabled. Law [2:1] FOVR 0 Backlight Sink Enable (BLSEN)--Register 0x05 Table 19. BLSEN Bit Map Bit 7 Reserved Bit 6 D7EN Bit 5 D6EN Bit 4 D5EN Bit 3 D4EN Bit 2 D3EN Bit 1 D2EN Bit 0 D1EN Table 20. Bit Descriptions for the BLSEN Register Bit Name N/A D7EN Bit No. 7 6 Description Reserved Diode 7 backlight sink enable 1 = selects LED7 as an independent sink 0 = connects LED7 sink to backlight enable (BL_EN) Diode 6 backlight sink enable 1 = selects LED6 as an independent sink 0 = connects LED6 sink to backlight enable (BL_EN) Diode 5 backlight sink enable 1 = selects LED5 as an independent sink 0 = connects LED5 sink to backlight enable (BL_EN) Diode 4 backlight sink enable 1 = selects LED4 as an independent sink 0 = connects LED4 sink to backlight enable (BL_EN) Diode 3 backlight sink enable 1 = selects LED3 as an independent sink 0 = connects LED3 sink to backlight enable (BL_EN) Rev. 0 | Page 29 of 48 D6EN 5 D5EN 4 D4EN 3 D3EN 2 ADP8863 Bit Name D2EN Bit No. 1 Description Diode 2 backlight sink enable 1 = selects LED2 as an independent sink 0 = connects LED2 sink to backlight enable (BL_EN) Diode 1 backlight sink enable 1 = selects LED1 as an independent sink 0 = connects LED1 sink to backlight enable (BL_EN) D1EN 0 Backlight Off Timeout (BLOFF)--Register 0x06 Table 21. BLOFF Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 OFFT Bit 2 Bit 1 Bit 0 Table 22. Bit Descriptions for the BLOFF Register Bit Name N/A OFFT Bit No. 7 [6:0] Description Reserved. Backlight off timeout. After the off timeout (OFFT) period, the backlight turns off. If the dim timeout (DIMT) is enabled, the off timeout starts after the dim timeout. 0000000 = timeout disabled 0000001 = 1 sec 0000010 = 2 sec 0000011 = 3 sec ... 1111111 = 127 sec Backlight Dim Timeout (BLDIM)--Register 0x07 Table 23. BLDIM Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 DIMT Bit 2 Bit 1 Bit 0 Table 24. Bit Descriptions for the BLDIM Register Bit Name N/A DIMT Bit No. 7 [6:0] Description Reserved. Backlight dim timeout. After the dim timeout (DIMT) period, the backlight is set to the dim current value. The dim timeout starts after the backlight reaches the maximum current. 0000000 = timeout disabled 0000001 = 1 sec 0000010 = 2 sec 0000011 = 3 sec ... 1111111 = 127 sec Rev. 0 | Page 30 of 48 ADP8863 Backlight Fade (BLFR)--Register 0x08 Table 25. BLFR Bit Map Bit 7 Bit 6 Bit 5 BL_FO Bit 4 Bit 3 Bit 2 Bit 1 BL_FI Bit 0 Table 26. Bit Descriptions for the BLFR Register Bit Name BL_FO Bit No. [7:4] Description Backlight fade out rate. If fade out is disabled (BL_FO = 0000), the backlight changes instantly (within 100 ms). If the fade out rate is set, the backlight fades from its current value to the dim or the off value. The times listed for BL_FO are for a full-scale fade out (30 mA to 0 mA). Fades between closer current values reduce the fade time. See the Automated Fade In and Fade Out Section for more information. 0000 = 0.1 sec (fade out disabled) 1 0001 = 0.3 sec 0010 = 0.6 sec 0011 = 0.9 sec 0100 = 1.2 sec 0101 = 1.5 sec 0110 = 1.8 sec 0111 = 2.1 sec 1000 = 2.4 sec 1001 = 2.7 sec 1010 = 3.0 sec 1011 = 3.5 sec 1100 = 4.0 sec 1101 = 4.5 sec 1110 = 5.0 sec 1111 = 5.5 sec Backlight fade in rate. If fade in is disabled (BL_FI = 0000), the backlight changes instantly (within 100 ms). If the fade in rate is set, the backlight fades from its current value to its maximum value when the backlight is turned on. The times listed for BL_FI are for a full-scale fade in (0 mA to 30 mA). Fades between closer current values reduce the fade time. See the Automated Fade In and Fade Out Section for more information. 0000 = 0.1 sec (fade in disabled)1 0001 = 0.3 sec 0010 = 0.6 sec 0011 = 0.9 sec ... 1111 = 5.5 sec BL_FI [3:0] 1 When fade in and fade out are disabled, the backlight does not instantly fade, but instead, fades rapidly within about 100 ms. Rev. 0 | Page 31 of 48 ADP8863 Backlight Level 1 (Daylight) Maximum Current Register (BLMX1)--Register 0x09 Table 27. BLMX1 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 BL1_MC Bit 2 Bit 1 Bit 0 Table 28. Bit Descriptions for the BLMX1 Register Bit Name N/A BL1_MC Bit No. 7 [6:0] Description Reserved. Backlight Level 1 (daylight) maximum current. The backlight maximum current can be set according to the linear or square law function (see Table 29 for a complete list of values). DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Table 29. Linear and Square Law Currents Per DAC Code (SCR = 0) DAC Code 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F 0x20 0x21 Linear Law (mA) 0 0.236 0.472 0.709 0.945 1.181 1.417 1.654 1.890 2.126 2.362 2.598 2.835 3.071 3.307 3.543 3.780 4.016 4.252 4.488 4.724 4.961 5.197 5.433 5.669 5.906 6.142 6.378 6.614 6.850 7.087 7.323 7.559 7.795 Square Law (mA) 1 0.000 0.002 0.007 0.017 0.030 0.047 0.067 0.091 0.119 0.151 0.186 0.225 0.268 0.314 0.365 0.419 0.476 0.538 0.603 0.671 0.744 0.820 0.900 0.984 1.071 1.163 1.257 1.356 1.458 1.564 1.674 1.787 1.905 2.026 DAC Code 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F 0x40 0x41 0x42 0x43 Rev. 0 | Page 32 of 48 Linear Law (mA) 8.031 8.268 8.504 8.740 8.976 9.213 9.449 9.685 9.921 10.157 10.394 10.630 10.866 11.102 11.339 11.575 11.811 12.047 12.283 12.520 12.756 12.992 13.228 13.465 13.701 13.937 14.173 14.409 14.646 14.882 15.118 15.354 15.591 15.827 Square Law (mA) 1 2.150 2.279 2.411 2.546 2.686 2.829 2.976 3.127 3.281 3.439 3.601 3.767 3.936 4.109 4.285 4.466 4.650 4.838 5.029 5.225 5.424 5.627 5.833 6.043 6.257 6.475 6.696 6.921 7.150 7.382 7.619 7.859 8.102 8.350 ADP8863 DAC Code 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F 0x60 0x61 0x62 0x63 Linear Law (mA) 16.063 16.299 16.535 16.772 17.008 17.244 17.480 17.717 17.953 18.189 18.425 18.661 18.898 19.134 19.370 19.606 19.842 20.079 20.315 20.551 20.787 21.024 21.260 21.496 21.732 21.968 22.205 22.441 22.677 22.913 23.150 23.386 Square Law (mA) 1 8.601 8.855 9.114 9.376 9.642 9.912 10.185 10.463 10.743 11.028 11.316 11.608 11.904 12.203 12.507 12.814 13.124 13.439 13.757 14.078 14.404 14.733 15.066 15.403 15.743 16.087 16.435 16.787 17.142 17.501 17.863 18.230 DAC Code 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F 0x70 0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E 0x7F 1 Linear Law (mA) 23.622 23.858 24.094 24.331 24.567 24.803 25.039 25.276 25.512 25.748 25.984 26.220 26.457 26.693 26.929 27.165 27.402 27.638 27.874 28.110 28.346 28.583 28.819 29.055 29.291 29.528 29.764 30.000 Square Law (mA) 1 18.600 18.974 19.351 19.733 20.118 20.507 20.899 21.295 21.695 22.099 22.506 22.917 23.332 23.750 24.173 24.599 25.028 25.462 25.899 26.340 26.784 27.232 27.684 28.140 28.599 29.063 29.529 30.000 Cubic 10 and Cubic 11 laws use the square law DAC setting but vary the time step per DAC code (see the Automated Fade In and Fade Out section). Rev. 0 | Page 33 of 48 ADP8863 Backlight Level 1 (Daylight) Dim Current Register (BLDM1)--Register 0x0A Table 30. BLDM1 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 BL1_DC Bit 2 Bit 1 Bit 0 Table 31. Bit Descriptions for the BLDM1 Register Bit Name N/A BL1_DC Bit No. 7 [6:0] Description Reserved. Backlight Level 1 (daylight) dim current. The backlight is set to the dim current value after a dim timeout or if the DIM_EN flag is set by the user (see Table 29 for a complete list of values). DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Backlight Level 2 (Office) Maximum Current Register (BLMX2)--Register 0x0B Table 32. BLMX2 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 BL2_MC Bit 2 Bit 1 Bit 0 Table 33. Bit Descriptions for the BLMX2 Register Bit Name N/A BL2_MC Bit No. 7 [6:0] Description Reserved. Backlight Level 2 (office) maximum current (see Table 29 for a complete list of values). DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Rev. 0 | Page 34 of 48 ADP8863 Backlight Level 2 (Office) Dim Current Register (BLDM2)--Register 0x0C Table 34. BLDM2 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 BL2_DC Bit 2 Bit 1 Bit 0 Table 35. Bit Descriptions for the BLDM2 Register Bit Name N/A BL2_DC Bit No. 7 [6:0] Description Reserved. Backlight Level 2 (office) dim current. See Table 29 for a complete list of values. The backlight is set to the dim current value after a dim timeout or if the DIM_EN flag is set by the user. DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Backlight Level 3 (Dark) Maximum Current Register (BLMX3)--Register 0x0D Table 36. BLMX3 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 BL3_MC Bit 2 Bit 1 Bit 0 Table 37. Bit Descriptions for the BLMX3 Register Bit Name N/A BL3_MC Bit No. 7 [6:0] Description Reserved. Backlight Level 3 (dark) maximum current. See Table 29 for a complete list of values. DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Rev. 0 | Page 35 of 48 ADP8863 Backlight Level 3 (Dark) Dim Current Register (BLDM3)--Register 0x0E Table 38. BLDM3 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 BL3_DC Bit 2 Bit 1 Bit 0 Table 39. Bit Descriptions for the BLDM3 Register Bit Name N/A BL3_DC Bit No. 7 [6:0] Description Reserved. Backlight Level 3 (dark) dim current. See Table 29 for a complete list of values. The backlight is set to the dim current value after a dim timeout or if the DIM_EN flag is set by the user. DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 INDEPENDENT SINK REGISTER DESCRIPTIONS Independent Sink Current Fade Control Register (ISCFR)--Register 0x0F Table 40. ISCFR Bit Map Bit 7 Bit 6 Bit 5 Bit 4 Reserved Bit 3 Bit 2 Bit 1 Bit 0 SC_LAW Table 41. Bit Descriptions for the ISCFR Register Bit Name N/A SC_LAW Bit No. [7:2] [1:0] Description Reserved Independent sink current fade transfer law 00 = linear law DAC, linear time steps 01 = square law DAC, linear time steps 10 = square law DAC, nonlinear time steps (Cubic 10) 11 = square law DAC, nonlinear time steps (Cubic 11) Independent Sink Current Control (ISCC)--Register 0x10 Table 42. ISCC Bit Map Bit 7 Reserved Bit 6 SC7_EN Bit 5 SC6_EN Bit 4 SC5_EN Bit 3 SC4_EN Bit 2 SC3_EN Bit 1 SC2_EN Bit 0 SC1_EN Table 43. Bit Descriptions for the ISCC Register Bit Name N/A SC7_EN Bit No. 7 6 Description Reserved This enable acts upon LED7 1 = SC7 is turned on 0 = SC7 is turned off This enable acts upon LED6 1 = SC6 is turned on 0 = SC6 is turned off This enable acts upon LED5 1 = SC5 is turned on 0 = SC5 is turned off Rev. 0 | Page 36 of 48 SC6_EN 5 SC5_EN 4 ADP8863 Bit Name SC4_EN Bit No. 3 Description This enable acts upon LED4. 1 = SC4 is turned on. 0 = SC4 is turned off. This enable acts upon LED3. 1 = SC3 is turned on. 0 = SC3 is turned off. This enable acts upon LED2. 1 = SC2 is turned on. 0 = SC2 is turned off. This enable acts upon LED1. 1 = SC1 is turned on. 0 = SC1 is turned off. SC3_EN 2 SC2_EN 1 SC1_EN 0 Independent Sink Current Time (ISCT1)--Register 0x11 Table 44. ISCT1 Bit Map Bit 7 Bit 6 SCON Bit 5 Bit 4 SC7OFF Bit 3 Bit 2 SC6OFF Bit 1 Bit 0 SC5OFF Table 45. Bit Descriptions for the ISCT1 Register Bit Name SCON Bit No. [7:6] Description 1, 2 SC on time. If the SCxOFF time is not disabled and the independent current sink is enabled (Register 0x10), the LED(s) remains on for the time selected (per the following list) and then turns off. 00 = 0.2 sec 01 = 0.6 sec 10 = 0.8 sec 11 = 1.2 sec SC7OFF [5:4] SC7 off time. When the SC off time is disabled, the ISC remains on while enabled. When the SC off time is set to any other value, the ISC turns off for the off time (per the following listed times) and then turns on according to the SCON setting. 00 = off time disabled 01 = 0.6 sec 10 = 1.2 sec 11 = 1.8 sec SC6 off time. When the SC off time is disabled, the ISC remains on while enabled. When the SC off time is set to any other value, the ISC turns off for the off time (per the following listed times) and then turns on according to the SCON setting. 00 = off time disabled 01 = 0.6 sec 10 = 1.2 sec 11 = 1.8 sec SC5 off time. When the SC off time is disabled, the ISC remains on while enabled. When the SC off time is set to any other value, the ISC turns off for the off time (per the following listed times) and then turns on according to the SCON setting. 00 = off time disabled 01 = 0.6 sec 10 = 1.2 sec 11 = 1.8 sec SC6OFF [3:2] SC5OFF [1:0] 1 2 An independent sink remains on continuously when SCx_EN = 1 and SCxOFF = 00 (disabled). To enable multiple independent sinks, set the appropriate SCx_EN bits. To create equivalent blinking and fading sequences, enable all independent sinks in one write cycle to cause a preprogrammed sequence to start simultaneously. Rev. 0 | Page 37 of 48 ADP8863 Independent Sink Current Time (ISCT2)--Register 0x12 Table 46. ISCT2 Bit Map Bit 7 Bit 6 SC4OFF Bit 5 Bit 4 SC3OFF Bit 3 Bit 2 SC2OFF Bit 1 Bit 0 SC1OFF Table 47. Bit Descriptions for the ISCT2 Register Bit Name SC4OFF Bit No. [7:6] Description 1, 2 SC4 off time. When the SC off time is disabled, the ISC remains on while enabled. When the SC off time is set to any other value, the ISC turns off for the off time (per the following listed times) and then turns on according to the SCON setting. 00 = off time disabled 01 = 0.6 sec 10 = 1.2 sec 11 = 1.8 sec SC3 off time. When the SC off time is disabled, the ISC remains on while enabled. When the SC off time is set to any other value, the ISC turns off for the off time (per the following listed times) and then turns on according to the SCON setting. 00 = off time disabled 01 = 0.6 sec 10 = 1.2 sec 11 = 1.8 sec SC2 off time. When the SC off time is disabled, the ISC remains on while enabled. When the SC off time is set to any other value, the ISC turns off for the off time (per the following listed times) and then turns on according to the SCON setting. 00 = off time disabled 01 = 0.6 sec 10 = 1.2 sec 11 = 1.8 sec SC1 off time. When the SC off time is disabled, the ISC remains on while enabled. When the SC off time is set to any other value, the ISC turns off for the off time (per the following listed times) and then turns on according to the SCON setting. 00 = off time disabled 01 = 0.6 sec 10 = 1.2 sec 11 = 1.8 sec SC3OFF [5:4] SC2OFF [3:2] SC1OFF [1:0] 1 2 An independent sink remains on continuously when SCx_EN = 1 and SCxOFF = 00 (disabled). To enable multiple independent sinks, set the appropriate SCx_EN bits. To create equivalent blinking and fading sequences, enable all independent sinks in one write cycle. This causes a preprogrammed sequence to start simultaneously. Rev. 0 | Page 38 of 48 ADP8863 Independent Sink Current Fade (ISCF)--Register 0x13 Table 48. ISCF Bit Map Bit 7 Bit 6 Bit 5 SCFO Bit 4 Bit 3 Bit 2 Bit 1 SCFI Bit 0 Table 49. Bit Descriptions for the ISCF Register Bit Name SCFO Bit No. [7:4] Description Sink current fade out rate. The times listed here are for a full-scale fade out (30 mA to 0 mA). Fades between closer current values reduce the fade time. See the Automated Fade In and Fade Out section for more information. 0000 = disabled 0001 = 0.30 sec 0010 = 0.60 sec 0011 = 0.90 sec 0100 = 1.2 sec 0101 = 1.5 sec 0110 = 1.8 sec 0111 = 2.1 sec 1000 = 2.4 sec 1001 = 2.7 sec 1010 = 3.0 sec 1011 = 3.5 sec 1100 = 4.0 sec 1101 = 4.5 sec 1110 = 5.0 sec 1111 = 5.5 sec Sink current fade in rate. The times listed here are for a full-scale fade in (0 mA to 30 mA). Fades between closer current values reduce the fade time. See the Automated Fade In and Fade Out section for more information. 0000 = disabled 0001 = 0.30 sec 0010 = 0.60 sec 0011 = 0.90 sec 0100 = 1.2 sec 0101 = 1.5 sec 0110 = 1.8 sec 0111 = 2.1 sec 1000 = 2.4 sec 1001 = 2.7 sec 1010 = 3.0 sec 1011 = 3.5 sec 1100 = 4.0 sec 1101 = 4.5 sec 1110 = 5.0 sec 1111 = 5.5 sec SCFI [3:0] Rev. 0 | Page 39 of 48 ADP8863 Sink Current Register LED7 (ISC7)--Register 0x14 Table 50. ISC7 Bit Map Bit 7 SCR Bit 6 Bit 5 Bit 4 Bit 3 SCD7 Bit 2 Bit 1 Bit 0 Table 51. Bit Descriptions for the ISC7 Register Bit Name SCR SCD7 Bit No. 7 [6:0] Description 1 = Sink Current 1. 0 = Sink Current 0. For Sink Current 0, use the following DAC code schedule (see Table 29 for a complete list of values). DAC Linear Law (mA) Square Law (mA) 0000000 0.000 0 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 For Sink Current 1, use the following DAC code schedule (see Table 52 for a complete list of values). DAC Linear Law (mA) Square Law (mA) 0000000 0.000 0 0000001 0.472 0.004 0000010 0.945 0.014 0000011 1.42 0.034 ... ... ... 1111111 60 60 Table 52. Linear and Square Law Currents for LED7 (SCR = 1) DAC Code 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 Linear Law (mA) 0.000 0.472 0.945 1.42 1.89 2.36 2.83 3.31 3.78 4.25 4.72 5.20 5.67 6.14 6.61 7.09 7.56 8.03 8.50 8.98 9.45 9.92 10.39 10.87 Square Law (mA) 1 0 0.004 0.014 0.034 0.06 0.094 0.134 0.182 0.238 0.302 0.372 0.45 0.536 0.628 0.73 0.838 0.952 1.076 1.206 1.342 1.488 1.64 1.8 1.968 DAC Code 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F Linear Law (mA) 11.34 11.81 12.28 12.76 13.23 13.70 14.17 14.65 15.12 15.59 16.06 16.54 17.01 17.48 17.95 18.43 18.90 19.37 19.84 20.31 20.79 21.26 21.73 22.20 Square Law (mA) 1 2.142 2.326 2.514 2.712 2.916 3.128 3.348 3.574 3.81 4.052 4.3 4.558 4.822 5.092 5.372 5.658 5.952 6.254 6.562 6.878 7.202 7.534 7.872 8.218 Rev. 0 | Page 40 of 48 ADP8863 DAC Code 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F 0x40 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 Linear Law (mA) 22.68 23.15 23.62 24.09 24.57 25.04 25.51 25.98 26.46 26.93 27.40 27.87 28.35 28.82 29.29 29.76 30.24 30.71 31.18 31.65 32.13 32.60 33.07 33.54 34.02 34.49 34.96 35.43 35.91 36.38 36.85 37.32 37.80 38.27 38.74 39.21 39.69 40.16 40.63 41.10 Square Law (mA) 1 8.57 8.932 9.3 9.676 10.058 10.45 10.848 11.254 11.666 12.086 12.514 12.95 13.392 13.842 14.3 14.764 15.238 15.718 16.204 16.7 17.202 17.71 18.228 18.752 19.284 19.824 20.37 20.926 21.486 22.056 22.632 23.216 23.808 24.406 25.014 25.628 26.248 26.878 27.514 28.156 DAC Code 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F 0x70 0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E 0x7F 1 Linear Law (mA) 41.57 42.05 42.52 42.99 43.46 43.94 44.41 44.88 45.35 45.83 46.30 46.77 47.24 47.72 48.19 48.66 49.13 49.61 50.08 50.55 51.02 51.50 51.97 52.44 52.91 53.39 53.86 54.33 54.80 55.28 55.75 56.22 56.69 57.17 57.64 58.11 58.58 59.06 59.53 60 Square Law (mA) 1 28.808 29.466 30.132 30.806 31.486 32.174 32.87 33.574 34.284 35.002 35.726 36.46 37.2 37.948 38.702 39.466 40.236 41.014 41.798 42.59 43.39 44.198 45.012 45.834 46.664 47.5 48.346 49.198 50.056 50.924 51.798 52.68 53.568 54.464 55.368 56.28 57.198 58.126 59.058 60 Cubic 10 and Cubic 11 laws use the square law DAC setting but vary the time step per DAC code (see the Automated Fade In and Fade Out section). Rev. 0 | Page 41 of 48 ADP8863 Sink Current Register LED6 (ISC6)--Register 0x15 Table 53. ISC6 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 SCD6 Bit 2 Bit 1 Bit 0 Table 54. Bit Descriptions for the ISC6 Register Bit Name N/A SCD6 Bit No. 7 [6:0] Description Reserved. Sink current. Use the following DAC code schedule (see Table 29 for a complete list of values). DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Sink Current Register LED5 (ISC5)--Register 0x16 Table 55. ISC5 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 SCD5 Bit 2 Bit 1 Bit 0 Table 56. Bit Descriptions for the ISC5 Register Bit Name N/A SCD5 Bit No. 7 [6:0] Description Reserved. Sink current. Use the following DAC code schedule (see Table 29 for a complete list of values). DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Sink Current Register LED4 (ISC4)--Register 0x17 Table 57. ISC4 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 SCD4 Bit 2 Bit 1 Bit 0 Table 58. Bit Descriptions for the ISC4 Register Bit Name N/A SCD4 Bit No. 7 [6:0] Description Reserved. Sink current. Use the following DAC code schedule (see Table 29 for a complete list of values): DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Rev. 0 | Page 42 of 48 ADP8863 Sink Current Register LED3 (ISC3)--Register 0x18 Table 59. ISC3 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 SCD3 Bit 2 Bit 1 Bit 0 Table 60. Bit Descriptions for the ISC3 Register Bit Name N/A SCD3 Bit No. 7 [6:0] Description Reserved. Sink current. Use the following DAC code schedule (see Table 29 for a complete list of values). DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Sink Current Register LED2 (ISC2)--Register 0x19 Table 61. ISC2 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 SCD2 Bit 2 Bit 1 Bit 0 Table 62. Bit Descriptions for the ISC2 Register Bit Name N/A SCD2 Bit No. 7 [6:0] Description Reserved. Sink current. Use the following DAC code schedule (see Table 29 for a complete list of values). DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Sink Current Register LED1 (ISC1)--Register 0x1A Table 63. ISC1 Bit Map Bit 7 Reserved Bit 6 Bit 5 Bit 4 Bit 3 SCD1 Bit 2 Bit 1 Bit 0 Table 64. Bit Descriptions for the ISC1 Register Bit Name N/A SCD1 Bit No. 7 [6:0] Description Reserved. Sink current. Use the following DAC code schedule (see Table 29 for a complete list of values). DAC Linear Law (mA) Square Law (mA) 0000000 0 0.000 0000001 0.236 0.002 0000010 0.472 0.007 0000011 0.709 0.017 ... ... ... 1111111 30 30 Rev. 0 | Page 43 of 48 ADP8863 COMPARATOR REGISTER DESCRIPTIONS Comparator Configuration (CCFG)--Register 0x1B Table 65. CCFG Bit Map Bit 7 Bit 6 FILT Bit 5 Bit 4 FORCE_RD Bit 3 L3_OUT Bit 2 L2_OUT Bit 1 L3_EN Bit 0 L2_EN Table 66. Bit Descriptions for the CCFG Register Bit Name FILT Bit No. [7:5] Description Filter setting for the CMP_IN light sensor. 000 = 80 ms 001 = 160 ms 010 = 320 ms 011 = 640 ms 100 = 1280 ms 101 = 2560 ms 110 = 5120 ms 111 = 10,240 ms Force a read of the CMP_IN light sensor while independent sinks are running, but the backlight is not. Reset by chip after the conversion is complete and L2_OUT and L3_OUT are valid. Ignored if the backlight is enabled. This bit is the output of the L3 comparator. This bit is the output of the L2 comparator. 1 = the L3 comparator is enabled for the CMP_IN comparator. 0 = the L3 comparator is disabled for the CMP_IN comparator. Note that the L3 comparator has priority over the L2 comparator. 1 = the L2 comparator is enabled for the CMP_IN comparator. 0 = the L2 comparator is disabled for the CMP_IN comparator. FORCE_RD L3_OUT L2_OUT L3_EN L2_EN 4 3 2 1 0 Second Comparator Configuration (CCFG2)--Register 0x1C Table 67. CCFG2 Bit Map Bit 7 Bit 6 FILT2 Bit 5 Bit 4 FORCE_RD2 Bit 3 L3_OUT2 Bit 2 L2_OUT2 Bit 1 L3_EN2 Bit 0 L2_EN2 Table 68. Bit Descriptions for the CCFG2 Register Bit Name FILT2 Bit No. [7:5] Description Filter setting for the CMP_IN2 light sensor. 000 = 80 ms 001 = 160 ms 010 = 320 ms 011 = 640 ms 100 = 1280 ms 101 = 2560 ms 110 = 5120 ms 111= 10,240 ms Force a read of the CMP_IN2 light sensor while independent sinks are running, but the backlight is not. Reset by chip after the conversion is complete and L2_OUT and L3_OUT are valid. Ignored if backlight is enabled. This bit is the output of the L3 comparator for the second light sensor. This bit is the output of the L2 comparator for the second light sensor. 1 = the L3 comparator is enabled for the CMP_IN2 comparator. 0 = the L3 comparator is disabled for the CMP_IN2 comparator. Note that the L3 comparator has priority over the L2 comparator. 1 = the L2 comparator is enabled for the CMP_IN2 comparator. 0 = the L2 comparator is disabled for the CMP_IN2 comparator. Rev. 0 | Page 44 of 48 FORCE_RD2 L3_OUT2 L2_OUT2 L3_EN2 L2_EN2 4 3 2 1 0 ADP8863 Comparator Level 2 Threshold (L2_TRP)--Register 0x1D Table 69. L2_TRP Bit Map Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 L2_TRP Bit 2 Bit 1 Bit 0 Table 70. Bit Descriptions for the L2_TRP Register Bit Name L2_TRP Bit No. [7:0] Description Comparator Level 2 threshold. If the comparator input is below L2_TRP, the comparator trips and the backlight enters Level 2 (office) mode. The following lists the code settings for the photosensor current: 00000000 = 0 A 00000001 = 4.3 A 00000010 = 8.6 A 00000011 = 12.9 A ... 11111010 = 1080 A ... 11111111 = 1106 A Although codes above 1111010 (250 decimal) are possible, they should not be used. Furthermore, the maximum value of L2_TRP + L2_HYS must not exceed 11111010 (250). Comparator Level 2 Hysteresis (L2_HYS)--Register 0x1E Table 71. L2_HYS Bit Map Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 L2_HYS Bit 2 Bit 1 Bit 0 Table 72. Bit Descriptions for the L2_HYS Register Bit Name L2_HYS Bit No. [7:0] Description Comparator Level 2 hysteresis. If the comparator input is above L2_TRP + L2_HYS, the comparator trips and the backlight enters Level 1 (daylight) mode. The following lists the code settings for the photosensor current hysteresis: 00000000 = 0 A 00000001 = 4.3 A 00000010 = 8.6 A 00000011 = 12.9 A ... 11111010 = 1080 A ... 11111111 = 1106 A Although codes above 11111010 (250 decimal) are possible, they should not be used. Furthermore, the maximum value of L2_TRP + L2_HYS must not exceed 11111010 (250). Rev. 0 | Page 45 of 48 ADP8863 Comparator Level 3 Threshold (L3_TRP)--Register 0x1F Table 73. L3_TRP Bit Map Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 L3_TRP Bit 2 Bit 1 Bit 0 Table 74. Bit Descriptions for the L3_TRP Register Bit Name L3_TRP Bit No. 7:0 Description Comparator Level 3 threshold. If the comparator input is below L3_TRP, the comparator trips and the backlight enters Level 3 (dark) mode. The following lists the code settings for photosensor current: 00000000 = 0 A 00000001 = 0.54 A 00000010 = 1.08 A 00000011 = 1.62 A ... 11111111 = 137.7 A Comparator Level 3 Hysteresis (L3_HYS)--Register 0x20 Table 75. L3_HYS Bit Map Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 L3_HYS Bit 2 Bit 1 Bit 0 Table 76. Bit Descriptions for the L3_HYS Register Bit Name L3_HYS Bit No. [7:0] Description Comparator Level 3 hysteresis. If the comparator input is above L3_TRP + L3_HYS, the comparator trips and the backlight enters Level 2 (office) mode. The following lists the code settings for photosensor current hysteresis: 00000000 = 0 A 00000001 = 0.54 A 00000010 = 1.08 A 00000011 = 1.62 A ... 11111111 = 137.7 A First Phototransistor Register: Low Byte (PH1LEVL)--Register 0x21 Table 77. PH1LEVL Bit Map Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 PH1LEV_LOW Bit 2 Bit 1 Bit 0 Table 78. Bit Descriptions for the PH1LEVL Register Bit Name PH1LEV_LOW Bit No. [7:0] Description Lower eight bits of the 13-bit conversion value for the first light sensor (Bit 7 to Bit 0). The value is updated every 80 ms (when the light sensor is enabled). This is a read-only register. Rev. 0 | Page 46 of 48 ADP8863 First Phototransistor Register: High Byte (PH1LEVH)--Register 0x22 Table 79. PH1LEVH Bit Map Bit 7 Bit 6 Reserved Bit 5 Bit 4 Bit 3 Bit 2 PH1LEV_HIGH Bit 1 Bit 0 Table 80. Bit Descriptions for the PH1LEVH Register Bit Name N/A PH1LEV_HIGH Bit No. [7:5] [4:0] Description Reserved. Upper five bits of the 13-bit conversion value for the first light sensor (Bit 12 to Bit 8). The value is updated every 80 ms (when the light sensor is enabled). This is a read-only register. Second Phototransistor Register: Low Byte (PH2LEVL)--Register 0x23 Table 81. PH2LEVL Bit Map Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 PH2LEV_LOW Bit 2 Bit 1 Bit 0 Table 82. Bit Descriptions for the PH2LEVL Register Bit Name PH2LEV_LOW Bit No. [7:0] Description Lower eight bits of the 13-bit conversion value for the second light sensor (Bit 7 to Bit 0). The value is updated every 80 ms (when the light sensor is enabled). This is a read-only register. Second Phototransistor Register: High Byte (PH2LEVH)--Register 0x24 Table 83. PH2LEVH Bit Map Bit 7 Bit 6 Reserved Bit 5 Bit 4 Bit 3 Bit 2 PH2LEV_HIGH Bit 1 Bit 0 Table 84. Bit Descriptions for the PH2LEVH Register Bit Name N/A PH2LEV_HIGH Bit No. [7:5] [4:0] Description Reserved Upper five bits of the 13-bit conversion value for the second light sensor (Bit 12 to Bit 8). The value is updated every 80 ms (when the light sensor is enabled). This is a read-only register. Rev. 0 | Page 47 of 48 ADP8863 OUTLINE DIMENSIONS PIN 1 INDICATOR 4.10 4.00 SQ 3.90 0.50 BSC 0.30 0.25 0.20 16 15 EXPOSED PAD 20 1 PIN 1 INDICATOR 5 11 2.65 2.50 SQ 2.35 TOP VIEW 0.80 0.75 0.70 SEATING PLANE 0.50 0.40 0.30 10 6 BOTTOM VIEW 0.25 MIN 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WGGD. Figure 50. 20-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 4 mm x 4 mm Body, Very Very Thin Quad (CP-20-10) Dimensions shown in millimeters Figure 51. Tape and Reel Orientation for LFCSP Units ORDERING GUIDE Model 1 ADP8863ACPZ-R7 ADP8863DBCP-EVALZ ADP886XMB1-EVALZ 1 Temperature Range -40C to +85C Package Description 20-Lead LFCSP_WQ, 7" Tape and Reel Daughter Card USB-to-I2C Adapter Board 08392-050 061609-B Package Option CP-20-10 Z = RoHS Compliant Part. I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors). (c)2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D08392-0-4/10(0) Rev. 0 | Page 48 of 48 |
Price & Availability of ADP8863DBCP-EVALZ
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |